background image

29 

18. - INSTALLATION INSTRUCTIONS FOR WALL MOUNTED TELEVISIONS 
                                      ADITIONAL REQUIREMENTS  

 

 
 
 

These Instructions detail the Installation Requirements for Wall Mounted Televisions when Installed 
above the Fire and should be considered with all other Installation Requirements of the Fire. 
 
IMPORTANT:   Due to the High Heat Output of the Fire The Installation Requirements of these  
                            Instructions MUST be Adhered To For Wall Mounted Televisions. 

  

IMPORTANT:   The Fire will affect the height and position of the Television therefore it is important 
                            to check what height position options are possible.   
 
18.1 - GENERAL 

Before continuing with the Television Installation it is important to determine if there is the  likelihood of the Chimney 
Breast becoming hot when the Icona is in operation. Some of these checks will only provide assistance if a fire has been 
previously installed. The following checks will assist but are not conclusive.  
a.  

 Typically Class 1 flues with Dry Lined Walls will normally have acceptable Wall Temperatures.

 

b.  

 If a gas fire was installed and the chimney breast shows any signs of over heating e.g. discoloured wall paper, then do not  

      consider  Installing a Wall Mounted Television as the Temperatures are likely to be too high. 

c.  

If a gas fire was installed and the Chimney Breast is finished in Wall Paper and shows no signs of temperature damage then the 

      Wall Temperatures are likely to be acceptable so the Installation can proceed.   

d.  

A Wall Mounted Television Must Not be sunk into the wall as it will not be in an acceptable ventilated position and this is only  

     acceptable if additional fan cooling ventilation is provided. It is also likely that higher temperatures from the flue within the  
      Chimney Breast will occur.  

e.  

The Wall Mounted Television must be mounted on a suitable bracket or angled bracket that meets the Television Manufactures 

      requirements and spaces the Television at least 35mm away from the Chimney Breast.  

f.  

After reading the Installation Requirements you should compare this with the preferred height position of the Television. 

 

18.2 -  TELEVISION INSTALLATION REQUIREMENTS FOR FIRES WITH TRIMS

 

Providing the Chimney Breast temperatures have been confirmed as detailed in the General Section,  testing of the Icona 600H.E. 
has shown that the actual Ambient Temperature of 90º Fahrenheit (32º Centigrade) can be achieved and should be suitable for the 
Installation of a Wall Mounted Television and the Installation Requirements are as follows. 

a.   

You 

Must 

take account of the Television Manufacturer’s Installation requirements provided within their Instructions. 

b

.   Where No Shelf is present the bottom edge of the Television must be mounted at least 200mm above the top of the Enclosure 

Opening see diagram. 

c.   

For the Fire fitted with either a Combustible Shelf/Fire Surround Mantels or Non Combustible Shelf/Fire Surround Mantels the 

bottom edge of the  Television must be at least 75mm above the shelf, see diagram.  

d.

   The Television can be Mounted Vertically if desired with a suitable Wall Bracket that spaces the back of the television  at least  

      35mm from the Chimney Breast Wall. 

e

.   To help provide the preferred viewing position a 15

º 

Angled Wall Mounting Bracket can be used for the Television Installation. 

      A wall bracket with a larger angle 

Must Not 

be used.  

f

.   It is recommended that, for aesthetic reasons, due consideration is given prior to Installation for the provision of mains 

 

electric, aerial, sound and any other Connections that may wish to be hidden behind the Television. A Qualified Electrician/

 

Specialist should be consulted.  

g

.   Check First for the positions of any wires within the wall before drilling for the fixings.                                                                                

h

.    Ensure the wall is sound and the wall fixings are secure and able to take the weight of  the Television.  

i

.     Before proceeding with the Installation confirm the preferred Height Position of the Television with the Customer.  

 

Содержание The Icona 600 H.E.



















































Отзывы: