Nu-Flame The Icona 600 H.E., Инструкция по использованию, установке и обслуживанию

Страница: 15 / 50

15
It is Important that you read the whole Section before proceeding with any Building Work.
As a Standard suitable Fire Surround is unlikely to be available a Fire Surround will have to be Purpose Made.
14.1 - FIRE SURROUND or SLIPS REQUIREMENTS -
REFERENCE SHOULD BE MADE TO THE DIAGRAMS
a. Stone, Slate or Marble Fire Surrounds or Slips and/or any adhesives used must have a 150 Degree Centigrade rating. Care should
be taken with Micro Marbles claiming to have a 150Centigrade Rating as they can suffer from odour, blistering and discolouration.
A Fire Surround consisting of both Combustible and Non Combustible materials can be used, however the following applies:
. The Lower Shelf or Hearth below the fire Must always be Non-Combustible.
. The Upper Shelf or Mantel above the fire can be either Combustible or Non Combustible, however for Combustible it Must be
positioned 150mm above the Enclosure Opening for shelves up to 150mm deep and raised 25mm for every 25mm of extra depth.
. Any side members of the Fire Surround can be either Combustible or Non Combustible, however for Combustible they Must be
at least 100mm from the Enclosure Opening for depths of up to 100mm deep and moved a further 25mm for every 25mm of
extra depth.
b. The Fire Surround design should take account of the preferred height position of the Fire and Enclosure Opening.
c. If a Wall Mounted Television is being considered then you should also consult Section 15 as this could determine the preferred
Height position of the Fire and Enclosure Opening.
d. The Fire Surround Back Panel or Slips must cater for a flat area around the opening to cater for the Trim.
The minimum sizes required for each trim are detailed below. You may wish to also have a border around the outside of the trim.
The Flat Area Sizes Required are shown below. Also those with an 100mm border are also shown below.
Minimum Flat Sizes for Trims 100mm Border Plus Minimum Flat Sizes for Trims
Width (mm) Height (mm) Width (mm) Height (mm)
Harmony Trim 670mm 425mm 870mm 625mm
Deluxe Trim 770mm 525mm 970mm 725mm
Grande Trim 1025mm 880mm 1225mm 880mm
Concept Trim 770mm 425mm 970mm 625mm
e. There are no limitations on the depth of Fire Surrounds Shelf/Mantel, for
Non Combustible Shelf/Mantels however where they are deeper than
150mm and below the minimum position of 150mm above the Enclosure
opening they will reduce the Radiant Heat.
It is therefore recommended that Natural Materials are used as some
Micro Marbles claiming 150 Centigrade Ratings as they can suffer from
odour, blistering and discolouration.
f. Provided the bottom of the Enclosure Opening is at least 250mm above
the floor there is no depth requirements for the Fire Surround base/hearth.
g. If the height above the floor to the Enclosure Opening is reduced below the
minimum of 250mm the depth of the Fire Surround base/hearth must be at
a minimum of 150mm depth.
h. The Enclosure must cater for a minimum depth of 330mm as shown.
i. You can recess both the Fire Surround Hearth/Shelf and Mantel into the
wall to provide support, however they must only be let into the wall to the
same depth as the Lintels. Lintels must still be used as the Shelf may not
provide enough structural support and could crack shortly after Installation
or some time in the future if Lintels are not used.
j. The Fire Surround back panel must be fully sealed to the Enclosure
Opening to ensure a good flue seal.
14.2 - WALL COVERINGS
With any form of heating appliance convection air will rise up past the fire carrying particles of dust that will in time result in varying
degrees of wall staining. The use of a Fire Surround and or Slips will help to reduce this effect.
a. A Fire Surround will contain the heat and it is therefore preferable to use a Surround Back Panel or Slips to shield the area
between the Enclosure Opening and Fire Surround as any Wall Covering may not withstand the temperatures in this area.
b. The fire provides an high heat output so we recommend that any wall coverings are best cut back to the outer edges of the Slips or
just within the outer edges of the Fire Surround.
c. Over time some staining might occur and we therefore suggest due consideration is taken when considering the use of patterned
paper around the Fire Surround or Slips.
Due to the heat output of The Icona 600H.E. it is not recommended to use blown vinyl wall covering around the fire.
14.3 - CLEARANCES TO COMBUSTIBLE MATERIALS
a. Any side members/walls of the Fire Surround can be either Combustible or Non Combustible, however for Combustible they Must
be at least 100mm from the Enclosure Opening for depths of up to 100mm deep and moved a further 25mm for every 25mm of
extra depth.
b. With all heating appliances, soft furnishings, decorations and wall coverings may discolour or scorch if placed too close.
c. No combustible material, e.g. curtains must be closer than 500mm to the Builders Opening.
14. - INSTALLATION FOR FIRES WITH TRIMS & FIRE SURROUND
BUILDING ENCLOSURE REQUIREMENTS & FIRE SURROUND REQUIREMENTS
If a Wall Mounted Television is being Considered Also Make Reference to Section 18
Fire Surround Applications for
Icona 600HE with Trims