Nu-Flame The Icona 600 H.E., Инструкция по использованию, установке и обслуживанию

Страница: 9 / 50

9
11. - GAS SUPPLY
Very Important : As Building Work will be required after Installing the Gas Supply Piping Ensure that
the Piping or Isolation Elbow is Sealed Off as Dust or Debris will Cause Major Problems.
It Is Recommended to Check The Next Section as Building Work May Affect the Gas Supply Routing.
a. Carry out a gas soundness test before working on the gas supply.
b. Gas supply provision should be made in accordance with the latest Gas Safety (Installation and Use) Regulations as amended.
c. Confirm that the fire has been supplied for the correct gas to be used by checking the Data Badge in the base of the fire.
d. The Gas Supply Pipe must be routed into the fire as detailed in ‘ e ‘. An isolation elbow is provided for the fire to be positioned at
the inlet. As mentioned seal off the isolation elbow outlet with for instance tape to prevent dust or debris entering the gas piping.
e. Your 8mm gas pipe route should be considered before any Building work is planned. A concealed gas supply inlet is provided
through the Debris Plate cut out in the base of the Burner Box at the right side of the fire. Route the Gas Pipe at a position of
228mm to the right of the centre line of the fire and 230mm from the front. The Gas Pipe should terminate 25mm below the base
of the cut out of the front opening. You will therefore need to determine the position of the base of the Building Opening fire
f. Where the gas supply passes through walls, floors, voids, concrete and wall cavities the supply should be sleeved.
g. Determine the gas supply pipe size required taking into account any other gas appliances.
h. Once the gas pipe fitted and its end position terminated purge the pipe of dust-debris as detailed in ’ I ’ and fit the 8mm
compression isolation/pressure test elbow provided.
i. In common with all other gas appliances, dirt and debris in the gas system can block the valve and gas injectors on this
appliance, and faults caused by this are not covered by the guarantee.
Therefore it is important that all gas pipes must be purged of both air and debris.
j. If you suspect that there may still be dirt and/or debris in the gas system, fit a filter in the pipeline, before the gas isolation/
pressure test elbow.
k. Do not use jointing compound on any compression fittings on the fire. The use of jointing compound on the compression joints
on this appliance will possibly invalidate the guarantee, as it can get into the control mechanism and cause a malfunction.
l. Seal off the isolation/pressure test elbow and check all gas connections for gas soundness before proceeding to fit the fire .
! IMPORTANT NOTE !
Always reseal the pressure test point and check that it is gas tight. (This accounts for a lot of recalls.)
The Installation Applications Options Are:
12.0 Installation for a Fire with Trim into a Class 1 or Lined Flue - Options:
Shelves both Combustible or Non Combustible.
13.0 Installation for a Trimless Fire into a Class 1 or Lined Flue - Options:
Shelves both Combustible or Non Combustible.
14.0 Installation for a Fire with Trim into Fire Surround or Slips in a Class 1 or Lined Flue.
15.0 Installation for a Trimless Fire into a Fire Surround or Slips in a Class 1 or Lined Flue.
16.0 Installation for a Fire with Trim into a False Chimney Breast with 5” Flue - Options:
Fire Surround.
Shelves both Combustible or Non Combustible.
17.0 Installation for a Trimless Fire into a False Chimney Breast with 5” Flue - Options:
Fire Surround.
Shelves both Combustible or Non Combustible.
18.0 Installation for a Wall Mounted Televisions - With Options Above.
IMPORTANT : ALL RELEVANT SECTIONS SHOULD BE CONSIDERED BEFORE ANY BUILDING WORK.
Sections 12 - 17 are for the various Installation Applications -
Only one will apply.
! IMPORTANT NOTE !
The chosen installation should have
been predetermined with any parts ordered before any
Building Work Is Started or Installing of the fire.