NSD Varlimit VS-212DN Скачать руководство пользователя страница 20

Страница: 20 / 144

3-2

3.2 Control Panel Display

VS-212DN is equipped with 2 LED lamps (MS and NS) which serve as DeviceNet status indicators.

The "MS" indicator shows the module status, and the "NS" indicator shows the network status.

MS Indicator

LED Status

VS-212DN Status

Description

OFF

No power

No power is being supplied.

Green ON

Normal

Normal operation is in progress.

Green blinking

No setting

Configuration is not completed or is incorrect.

Red blinking

Minor error

Recovery is possible by changing a setting, etc.

Red ON

Non-recovery error

VS-212DN recovery from this error is not possible.

Replacement is required.

Green/red blinking

Self-diagnosis

VS-212DN self-diagnosis is in progress.

NS Indicator

LED Status

VS-212DN Status

Description

OFF

No power or offline

No power is being supplied to the VS-212DN. Online status is not

established. ("MS" minor error, etc.)

Green blinking

Online/disconnected VS-212DN is not recognized by master unit.

Green ON

Online/connected

VS-212DN is recognized by master unit.

Red blinking

Minor

communication error Recovery is possible by changing a setting, etc.

Red ON

Critical error

Error which disables network communications.

(Duplicate node addresses, circuit malfunction, etc.)

Green/red blinking

VS-212DN communication failure.

Other Errors

LED Status

Description

Orange (simultaneous red and green) MS,

NS lamps are both ON

VS-212DN power voltage drop detected.

MS and NS red ON

A DeviceNet CPU watchdog timer error has occurred.

MS red ON, NS orange ON

Watchdog timer error has occurred at both the DeviceNet CPU and the

control CPU.

MS red ON, NS unchanged

(communication enabled)

A watchdog timer error has occurred at the control CPU.

MS orange ON, NS unchanged

(communication enabled)

Communication error has occurred at the control CPU and at the

DeviceNet CPU. Recovery is possible by clearing the communication

error status.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды