NSD Varlimit VS-212DN Скачать руководство пользователя страница 46

Страница: 46 / 144

4-7

4.6 Explanation of I/O

4.6.1 Terminal Block I/O

(1) READY output

This output switches ON when the following conditions are satisfied (same as READY LED):

o RUN mode

o There is no error.

(2) STOP 1 / 2 (B-contact)

The STOP input signals stop positioning operations. When positioning operations are executed,

these signals should be ON. When the STOP input is OFF, all positioning operations will be

disabled and all motor control outputs will be switched OFF.

STOP 1 used for axis 1 and STOP 2 used for axis 2.

4.6.2 Connector I/O

(1) Forward output

Motor control output for positioning operation.

“Speed switching” format: Forward

“Speed stepping” format: Forward/low-speed

(2) Reverse output

Motor control output for positioning operation.

“Speed switching” format: Reverse

“Speed stepping” format: Reverse/low-speed

(3) High-speed output

Motor control output for positioning operation.

(4) Low-speed / Medium-speed output

Motor control output for positioning operation.

“Speed switching” format: Low-speed

“Speed stepping” format: Medium-speed

(5) Brake release output

Brake release output for positioning operation

(6) In-position output

This output switches ON at positioning completed when the current position value enters

the “In-position” zone.

(7) Positioning in progress output

This signal switches ON during positioning operations.

(8) Operation error output

This signal switches ON during positioning operations when an error occurs.

(9) Current position value preset 1/ 2 output

This signal is used to execute the current position preset operation. When this input signal

switches ON, the current position preset operation will be executed.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды