NSD Varlimit VS-212DN Скачать руководство пользователя страница 48

Страница: 48 / 144

5-2

5.2 Changing Saved Data

The VS-212DN handles the following 2 types of data.

(1) Data which is saved internally in the VS-212DN.

- Initial settings data

- Parameter data

- Limit switch data (Program Nos.1-8)

(2) Data which is not saved at the VS-212DN.

- Buffer memory data (limit switch data)

In order to operate the VS-212DN the (1) data items shown above must be written to memory.

Generally speaking, the (2) data changes as operation proceeds.

Data saved internally in the VS-212DN (initial settings, parameter data, limit switch data) can be

changed by either of the following 2 methods.

(1)From an external setting unit (VS-T62 or VS-T62B).

(2)From the PLC.

Note:

The VS-212DN mode must be changed in order to change the data which has been saved internally.

Modes selected from an external setting device are referred to as a "Manual" modes, and modes selected

from the PLC are referred to as "Sequence" modes.

Sequence mode selections from the PLC can occur only when the Manual mode is RUN or TEST.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды