NSD Varlimit VS-212DN Скачать руководство пользователя страница 6

Страница: 6 / 144

3.5.10 Preset Value Writing for Current Position Preset Input

............ 3-18

3.5.11 Current Position Preset ‘Input Disabled’ Setting (Writing) ............ 3-18
3.5.12 Target Stop Position Writing

................................................. 3-19

3.5.13 Forward/Reverse Stop Zone After Learning Function (Reading) ... 3-19
3.5.14 Speed Limit Writing

............................................................. 3-19

3.5.15 Buffer Memory Selection For Positioning Pattern Data (Writing) ... 3-19
3.5.16 Medium-Speed Zone Writing

................................................. 3-19

3.5.17 Low-Speed Zone Writing ............................................................. 3-20
3.5.18 FWD/RVS Stop Zone Writing

................................................. 3-20

3.5.19 In-Position Zone Writing ............................................................. 3-20
3.5.20 Limit Switch Output Status Reading

.................................... 3-20

3.5.21 Program No. Answerback Reading

.................................... 3-21

3.5.22 Limit Switch “Output Disabled” Setting (Writing) ........................ 3-21
3.5.23 Program No. Setting (Writing)

................................................. 3-21

4. Function List

.................................................................................................. 4-1

4.1 Current Position Detection Function

................................................. 4-2

4.2 Positioning Function

......................................................................... 4-3

4.3 Limit Switch Output Function

............................................................. 4-4

4.4 Nomenclature

...................................................................................... 4-5

4.5 Explanation of Displays

......................................................................... 4-5

4.5.1 System LEDs

......................................................................... 4-5

4.5.2 DeviceNet monitor LEDs (MS, NS)

.................................... 4-5

4.5.3 Monitor Display

......................................................................... 4-6

4.6 Explanation of I/O ...................................................................................... 4-7

4.6.1 Terminal Block I/O

............................................................. 4-7

4.6.2 Connector I/O

......................................................................... 4-7

5. Operations

.................................................................................................. 5-1

5.1 Operating Sequence (Flowchart)

............................................................. 5-1

5.2 Changing Saved Data

......................................................................... 5-2

5.3 Connecting External Wiring

............................................................. 5-3

5.3.1 Wiring precautions

............................................................. 5-3

5.3.2 Connecting The External Power Supply .................................... 5-3

5.4 ABSOCODER Sensor Installation Precautions

.................................... 5-4

5.4.1 Installation of MRE series ABSOCODER sensor ........................ 5-4
5.4.2 Precautions when connecting ABSOCODER sensor

............ 5-4

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды