NSD Varlimit VS-212DN Скачать руководство пользователя страница 33

Страница: 33 / 144

3-15

3.5.1 Manual Mode Input/Output Status Reading

The following status are read.

(1) Manual mode using the VS-T62 or VS-T62B

The bit which corresponds to the selected manual mode (specified from the external setting

unit VS-T62 or VS-T62B) is set to "1". If the external setting unit is not being used, "B0"

becomes "1".

(2) Current position preset input status

Becomes "1" when the relevant current position preset input switches on.

(3) Output status

Becomes "1" when the relevant output switches on.

3.5.2 Error Code Reading

Error codes are read when errors occur. Error codes can be cleared by the following operations.

(1) Turn the "error reset" (command 1: 6 bit) command on from the sequence data.

(2) Turn the power off.

(3) Press the [CLR] key at the external setting unit (VS-T62 or VS-T62B).

(4) Change the Manual mode's mode (mode selected from external setting device).

(5) Change the Sequence mode's mode (mode selected from PLC).

3.5.3 Function Selection (Parameter Writing)

VS-212DN offers the following settings: "0" (joint usage for positioning), "1"(limit switch output only),

and "2" (current position detection only). However, only the "0" setting should be selected (this is the

default setting). Operation cannot be guaranteed if any setting other than "0" is selected.

3.5.4 Sequence Mode Selection Writing

This is the area where the appropriate mode for data writing conditions is selected when writing the

parameter data and the limit switch output ON/OFF data from the PLC CPU. This mode is selected by

the PLC CPU. Therefore, this is called 'sequence mode' to distinguish it from the mode (manual

mode) selected by the VS-T62 or VS-T62B.

Set '1' to the bit corresponding to the desired sequence mode when RUN or TEST in manual mode is

selected. Set '0' to other bits. Setting '1' to both bits will cause an error. The data written to the

buffer memory for data communication with the PC CPU is loaded to the VS-212DN when the PLC

Ready signal (command 1: 7 bit) is turned ON in sequence mode.

Even when sequence mode is selected, if manual mode is changed o anything other than RUN or

TEST, priority is given to manual mode.

(a) Current position is set by INIT in sequence mode.

(b) Program is written by PRGM in sequence mode

Set '1' when writing in the above cases. Become “0” as a default value when power ON.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды