NSD Varlimit VS-212DN Скачать руководство пользователя страница 82

Страница: 82 / 144

7-14

7.1.9 Current position presetting during positioning operation

The ‘current position preset’ function is operative even when positioning is in progress. The resulting

operation is explained below.

(1) When the positioning direction is not changed as a result of the preset function:

The positioning operation is not interrupted.

However, because positioning control will now be based the current position value which exists

after the current position preset function is executed, the speed may be switched from high-speed

to medium-speed or low-speed after the current position preset function occurs, depending on the

new position’s distance from the target position.

(2) When the positioning direction is reverse as a result of the current position preset function:

Positioning will be stopped (emergency stop), and after a ‘stop detection’ has occurred, positioning

toward the target position will be re-started based on the current position value which exists after

the current position preset function is executed.

After being re-started, positioning occurs in the normal manner.

(3) When the current position value enters the stop zone as a result of the current position preset function:

Positioning will be stopped (emergency stop), and after a ‘stop detection’ has occurred, a ‘START

from stop zone’ operation will automatically be executed, with positioning being based on the

current position value which exists after the current position preset function is executed.

However if the ‘START from stop zone disabled’ parameter setting has been designated,

positioning will not be re-started once the stop zone has been entered.

(4) The VS-212DN automatically recognizes a ‘stop status; (stop detection) when the change in the

current position value per each 100 ms is plus/minus 2 bits (expresses as sensor binary value).

(5) The current position preset function can be disabled during positioning operations by designating a

‘1’ setting (sequence program setting) for the input signal bit corresponding to the buffer memory’s

current position preset ‘input disabled’ setting (I/O address: 16391 [16455]) address.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды