NSD Varlimit VS-212DN Скачать руководство пользователя страница 50

Страница: 50 / 144

5-4

5.4 ABSOCODER Sensor Installation Precautions

This section explains precautions for ABSOCODER sensor installation.

5.4.1 Installation of MRE series ABSOCODER sensor

Installation of the ABSOCODER sensor must be executed according to the dimensions shown in

the drawings.

Although the MRE sensor is more rugged than general optical encorders, care should be taken

nevertheless to avoid shocks and unbalanced loads upon installation. For example, if an

excessive radial load or thrust load is applied to the shaft-end, the sensor accuracy could be

compromised. To avoid such problems, a suitable coupling method is recommended.

5.4.2 Precautions when connecting ABSOCODER sensor

(1) Connection should be made using the special cable, with the connector being securely

tightened.

(2) If further length is desired, an extension cable (with connector) must be ordered separately.

Refer to Item 2.7 for details regarding extension cables.

(3) The maximum length for which extension is possible varies according to the ABSOCODER

sensor model which is used. Refer to Item 2.6 for details.

(4) A robotic cable must be used if the special ABSOCODER sensor cable is to be used at a

movable area of the system. In such a case, the cable should never be bent to from a radius of

less than 75mm.

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды