NSD Varlimit VS-212DN Скачать руководство пользователя страница 54

Страница: 54 / 144

6-4

6.3.1 Sensor selection/sensor rotation direction setting (I/O address: 16392 [16456])

The direction of rotation in which the position data value increases are designated as either “CW” or

“CCW” (viewed from sensor shaft direction) and sensor type.

(1) CW direction

In this direction, the current position value increases.

(2) CCW direction

In this direction, the current position value increases.

Setting data

Sensor type

Rotation direction

MRE-32SP062

CCW

MRE-G[ ]SP062

CCW

No sensor

6.3.2 Decimal point position setting (I/O address: 16393 [16457])

The decimal point position is set for the display area of the external setting unit (VS-T62 or

VS-T62B). This setting does not affect the binary data used for the PLC. The decimal point

position is determined by the number of digits after the decimal point.

Setting data

Decimal point position

0.0

0.00

0.000

0.0000

0.00000

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды