NSD Varlimit VS-212DN Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 144

background image

9-1

9. TROUBLESHOOTING

VS-212DN operation errors and troubleshooting procedures are described in this section.

9-1. Error Code List

When an error occurs at the VS-212DN, the corresponding

error code is saved in the buffer memory (I/O address: 2 [3])

and at the monitor display. At this time, the error detection

(status address 0 and 1: 5 bits) signal switches on, and the

READY output switches off (READY LED goes off).

The error code for the most recent error which occurred

displays on the monitor (this applies to both axes 1 and 2).

The status address 0 and 1: 0-4 bits switch on in accordance

with the error content. If a positioning error occurs, an operation

error (status address 6 and 7: 7 bits, input/output connector:

A5, B5) switches on.

Error Type

Error

code

Description

When

Detected

Countermeasure

'Buffer
memory
writing
prohibited'
errors

10 Activated when

writing (by sequence
program 'TO'
instruction) is
attempted at a buffer
memory addresses
(writing prohibited).

Current position value area
(scaling binary)

During online
status

Revise the sequence program
so that writing is not attempted
at a 'writing prohibited' area of
the buffer memory.

12

Current position value area
(sensor binary)

14

Limit switch output status area

15

Program No. answerback area

16

Manual mode area

17

Error code area

18

Speed output area
Hold current position area
(scaling binary)
Hold current position area
(sensor binary)
FWD stop zone area after learning
RVS stop zone area after learning
Sequence mode answerback area

Detection
errors

20

VS-212DN detected an 'upper-limit overtravel' condition.

During online
status

- Move the machine back within the

'lower-limit to upper-limit' range.

- Revise the positioning setting data.
- Revise the positioning parameter

settings.

- Revise the 'lower-limit/upper-limit'

settings.

21

VS-212DN detected a 'lower-limit overtravel' condition.

22

VS-212DN detected a sensor error. Sensor error causes as follows:
- ABSOCODER sensor is disconnected.
- Severed/disconnected ABSOCODER sensor cable.
- ABSOCODER sensor failure.
- No external power supply.
- Malfunction in VS-212DN position detection circuit.

Always

- Connect the ABSOCODER sensor if

disconnected.

- Replace the ABSOCODER sensor.
- Check the electrical condition of the

sensor cable. (continuity, shorts)

- If the problem appears to be caused by a

malfunction at the VS-212DN position detection
circuit, please contact your service representative.

23

VS-212DN detected an excessive correction amount (during preset
operation). 'Excessive correction amount' causes are as follows:

- Misalignment between ABSOCODER sensor's detected position and

actual position, caused by machine slippage, backlash, etc.

- Deviation in the position where 'current position preset' input signal is

received.

- Incorrect 'permissible correction amount' parameter setting.

During 'current
position preset'
operation.
(In TEST
mode, and
when online)

- Adjust the machine.
- Revise the 'permissible

correction amount' parameter
setting.

«
...
114
115
116
117
118
...
»

Содержание Varlimit VS-212DN

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Varlimit VS-212DN

Бренд: Bartlett Страницы: 30

Бренд: Panasonic Страницы: 8

Бренд: Osram Страницы: 3

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: phytron Страницы: 55

Бренд: TCS Страницы: 8

Бренд: Chamberlain Страницы: 4

Бренд: Shimaden Страницы: 16

Бренд: HBM Страницы: 88

Бренд: MAKOT Страницы: 6

DuplicAir Intelligent Control Blue

Бренд: Jydepejsen Страницы: 52

Around the World Series

Бренд: X-lander Страницы: 41

Бренд: HIKVISION Страницы: 22

Бренд: Microchip Technology Страницы: 18

Бренд: Zenith Страницы: 11

Intellisys TBV-D

Бренд: Nor-Cal Products Страницы: 14

Бренд: Woodward Страницы: 84

Бренд: REMdevice Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды