NSD Varlimit VS-212DN Скачать руководство пользователя страница 35

Страница: 35 / 144

3-17

3.5.8 Speed Output Reading

The speed is detected by the ABSOCODER sensor is stored either as binary value of the change

amount in position within the specified time or as rotation speed (r/min.) The desired form is selected

by 'speed gate time'.

o Speed gate time: This is the time interval for detecting the sensor's travel speed. For the MRE-G[ ]

type ABSOCODER, the rotation speed is 1/gear ratio ([ ] / 32).

o Speed sampling time: This is the sampling time for the speed gate time. This item is disabled if a

"rotation speed" is set at the speed gate time.

(1) When storing binary value (Any from 0 to 4 is selected by 'speed gate time'.)

The sensor's rotation speed is stored as sensor binary value. This means that the change in

amount of speed gate time is stored in the absolute value.

The graph below shows the gate time and the sampling time.

[When sampling time = 1/2 of gate time]

The next gate time starts when the current sampling has finished.

(2) When storing rotation speed ('5' is selected by 'speed gate time'.)

This area stores the rotation speed (r/min.) internally calculated according to the current position

detected by the ABSOCODER

Notes:

Speed with symbol is set regarding the rotation direction set by address 16386 [1702] (sensor

selection/sensor rotation direction) as 'positive (+)'.

'Negative (-)' rotation speed is stored as complement of '2'.

When using the MRE-G[ ] type ABSOCODER sensor, the rotation speed to be stored is 1/gear ratio

([ ]/32 ).

Содержание Varlimit VS-212DN

















































































































































Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды

NSD Varlimit VS-212DN, Руководство пользователя

Результаты поиска

Содержание Varlimit VS-212DN

Отзывы:

Похожие инструкции для Varlimit VS-212DN

Бренды по названию

Популярные бренды