NSC Sicherheitstechnik Solution F2 Скачать руководство пользователя | Manualshive

Страница: 43 / 49

background image

NSC Sicherheitstechnik GmbH

43/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

- configured device address

- error code ("new" in this exampel)

- programmed zone and detector number

By pressing the "ok" key each single detector can be stored in the FCP programming, by pressing "all ok"
all connected devices will be stored in the FCP flash memory simultaneously.

Checking of earth fault

A constant voltage must not be measurable between potential earth and fire control panel potential
there

Voltage between PE / - accumulator

Ο

o.k.

Ο

fault -> .............V

Voltage between PE / + accumulator

Ο

o.k.

Ο

fault -> .............V

In case of an earth fault this has to be localised by disconnecting single cables in the fire control
panel. Then the earth fault has to be removed. The supervision of an earth fault can be deactivated
by system parameter 13.

Measurement of loop voltage and current

Dependent of the used multimeter the voltage and the current will vary differently. This is caused by
the modulated protocol between the FCP and the loop devices. For the measurement of the current
the loop has to be separated on one side in the FCP and on the other side the current has to be
measured on the ML+ or ML- wire. At the same time the loop devices have to be in the quiescent
state. Decisive for a faultless operation is the fact, that all loop devices are supplied by a sufficient
voltage (17V). The voltage drop on the cable has to be calculated form the quiescent current and
the cable resistance measured under point 4.2.

Loop

Voltage

33V ± 3V

Quiescent

current

[mA]

Voltage drop[V]

(quiescent current x

cable resistance)

1

(ML-1-/ML-2-)

2

(ML-3-/ML-4-)

Configure power outputs

Load resistance               Tolerance

Power output 1   (0480)  : 0476 : 060
Power output 2   (1045)  : 1059 : 060
Power output 3   (0958)  : 0960 : 060
Power output 4   (0721)  : 0740 : 060

Cancel Calib. save

The thresholds depend on the load resistance of the connected device inclusive the line resistance. This
total resistance can be ascertained automatically for each power output individually by pressing "calib."
F3. The software then calculates the thresholds for open curcuit and short curcuit. The resistance can
also be measured with a multimeter and typed in directly using the keyboard.

«
...
41
42
43
44
45
...
»

Содержание Solution F2


















































Отзывы:

Нет отзывов

Похожие инструкции для Solution F2

Бренд: Magnescale Страницы: 132

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Kathrein Страницы: 16

Бренд: MAKOT Страницы: 6

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: ZKTeco Страницы: 6

Бренд: Eaton Страницы: 448

Бренд: Eaton Страницы: 57

Бренд: Absima Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды