NSC Sicherheitstechnik Solution F2 Скачать руководство пользователя | Manualshive

Страница: 27 / 49

background image

NSC Sicherheitstechnik GmbH

27/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

26

Revision                   Status

from zone         : 2          Normal

to zone           : 4          Normal

Cancel      On       Off

Menu „Revision“

The revision mode can be used to check the
detectors by detector test equipment (e.g. Solo test
equipment). When the detector is activated by the test
equipment the alarm is displayed at the FCP and
reset automatically if analogue value falls below the
alarm threshold.
Please type in the number of zones which shall be
investigated by the revision mode. Every line has to
be confirmed by “OK“.

Please activated the revision mode for the selected
zones by F2 („on“). Pay attention: the zones in
revision will be displayed at the panel as „disabled“.

The alarm of such a zone will be displayed in the LC
module as „T E S T A L A R M“

After finishing the revision do not forget to switch
off the revision mode by F3 („Off“) because an
alarm of these zones will not be transmitted to the
fire brigade.

The Apollo DISCOVERY sounder will be set in
configurstion mode by setting the group to revision.
This enables the functions to switch it on / off and
change volume setting by the magnetic wand.
After switching the revision off you cann accept or
discard the volume change of each sounder.

27

Settings 1

1. Date/Time        5. Delete program
2. System settings  6. Delete texts
3. Scan RS485       7. Delete Events
4. Scan detectors   8. Language

zurück               mehr       Enter

Settings 1 of FCP

1. To change date, time and day of the week

Jump to Menu

28

2. To enter sub menu for system settings

where some individual hardware and
software features can be configured

Jump to Menu

29

3. After pressing 3. LCD repeater panels

connected to serial interfaces will be
scanned. The number of found devices will
be displayed in the last but one display line

Jump to Menu

30

4. To enter sub menu for new scanning of

addressable detectors

Jump to Menu

31

5. To delete configuration of FCP. Before

deleting there will be a security inquiry

Jump to Menu

32

6. To delete detector texts. Before deleting

there will be a security inquiry

Jump to

Menu

33

7. To delete all events in event memory. Before

deleting there will be a security inquiry

Jump to Menu

34

8. To change the panel’s language

Jump to

Menu

35

For another settings menu please press F3 („more“)
to enter sub menu „Settings 2“

Jump to Menu

36

28

Date/Time
Day                : 09          Friday
Month              : 07          Winter

To set date and time

Please type the right data line by line and confirm
every line by OK.

«
...
25
26
27
28
29
...
»

Содержание Solution F2


















































Отзывы:

Нет отзывов

Похожие инструкции для Solution F2

Бренд: OmarLift Страницы: 14

Бренд: Vacon Страницы: 64

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 30

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 20

INDUSTRY PAN9028

Бренд: Panasonic Страницы: 34

Бренд: BEIER-Electronic Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды