NSC Sicherheitstechnik Solution F2 Скачать руководство пользователя | Manualshive

Страница: 9 / 49

background image

NSC Sicherheitstechnik GmbH

9/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

2. Menus for the end user:

The following description contains all the menus for the end user. If the push button „Prog"

is

pressed it starts with the main menu.

Nr.

LC-Display of Solution F2

Description

01

Main menu

1. Switch on/off
2. Alarm counter
3. End user code
4. Diagnosis

Cancel             Installer     Enter

General Main menu for end user

This menu appears immediately after pressing „Prog“.
The functions have the followings meanings :

1. To switch on / off detectors, input-/ output

modules, delay mode, zones and general
outputs

Jump to Menu

02

2. Indication of the alarm counter. It is a 4 digit

number (1 – 9999) Menü

03

3. To change the end user code

Jump to

Menu

04

4. To jump to the diagnosis menu

Jump to

Menu

05

The push button "cancel“ (F1) leads to the normal
status indication of the FCP.

The push button Installer (F3) is to use for the
installer company only. It leads to the menus for
service and configuration.

The push button „Enter“ (F4) selects (activates)
the function which is marked by a black
background. Instead you can also select the
function by pressing the no. left in front of the
functions (here : 1 – 4).

02

Switch on/off

1. Zones & detect. 5. Sounder/Strobe
2. Output          6. Alarm Trans.Dev.
3. Relay           7. Delay
4. Power Output    8. Fire Outputs

Cancel                           Enter

Main menu „Switch on / switch off“

1. Switching on/off of zones and detectors

Jump to Menu

02.1

2. Switching on/off of OC-Outputs

Jump to

Menu

02.3

3. Switching on/off of Relays inside the FCP

Jump to Menu

02.4

4. Switching on/off of 3 monitored power

outputs

Jump to Menu

02.5

5. Continuously switching on/off of sounders /

strobes (incl. loop sounders)

Jump to

Menu

02.6

6. Switching on/off the alarm transmission

device (TD)

Jump to Menu

02.7

7. To activate / deactivate the alarm delay for

the TD

Jump to Menu

02.8

8. Temporary switching on/off the fire

protection outputs. This means all outputs
will be deactivated until this function is
canceled. The fire protection outputs CAN
NOT be switched off during alarm state.

Jump to Menu

02.9

«
...
7
8
9
10
11
...
»

Содержание Solution F2


















































Отзывы:

Нет отзывов

Похожие инструкции для Solution F2

Бренд: Gantner Страницы: 56

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Dantherm Страницы: 96

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Gascat Страницы: 32

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: National Instruments Страницы: 8

Бренд: Eaton Страницы: 8

Бренд: U-Prox Страницы: 3

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренд: Lutron Electronics Страницы: 2

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Бренд: Simpnic Страницы: 16

Бренд: Water Specialist Страницы: 60

Бренд: aerl Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды