NSC Sicherheitstechnik Solution F2 Скачать руководство пользователя | Manualshive

Страница: 7 / 49

background image

NSC Sicherheitstechnik GmbH

7/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

one or two. It depends on the menu. Here we do not describe the function keys in details. Therefore

please have a look into section 2.

Please note that : usually there are the following standard functions for

„F1“ = „cancel“ or „back“. Means to leave the current menu and jump into the menu above, and

„F4“ = „Enter“. Means to select (or confirm) the function which is marked in the LC module by a

black background.

Description of the push buttons:

The control panel of the FCP "Solution F2“ is a high-quality membrane keypad. An intelligent circuit
detects any pressing of the push buttons and confirms it by a beep.

Push button :

Description :

By this push button the user leaves the normal operation display and enters the main
menu of the FCP. See the detailed description in section 2.

This push button deactivates (switch off) the external sounder outputs in case of an
alarm. This is a temporary deactivation because if another alarm comes in the
sounders will be activated again. It's also possible by this key to reactivate the
sounders manually.

This push button deactivates (switch off) the internal buzzer in case of an alarm or
fault message. This is a temporary deactivation because if another message comes in
the buzzer will be activated again.
In case of an alarm and delyed alarm transmission, the inspection time will be started.
If there is no alarm and no fault holding this push button activates an LED test.

This push button resets the FCP.

To reset a "key deposit alarm" message you have to enter the installer mode in main

menu. Afterwards the alarm can be reset it by this key.

Programmable function key (S1, S2). The setting could be done by the pC
configuration tool.

Use this push button in the menus to confirm your inputs line by line.

Use this push button in the menus to cancel your inputs.

Cursor control keypad.

Configuration:

The configuration of the fire control panel "Solution F2" has to be done generally by the PC configuration
software.
With Firmware release 1.00 and following the data communication between panel amd pc must be
enabled by user- or installercode. This requires as minimum release 6.0.0.0 of the configuration
software.
You need a standard USB cable USB-A to USB-B for connection between pc an panel.

«
...
5
6
7
8
9
...
»

Содержание Solution F2


















































Отзывы:

Нет отзывов

Похожие инструкции для Solution F2

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Vacon Страницы: 64

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренд: UNI Страницы: 21

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Бренд: GBD Страницы: 15

Бренд: Vaillant Страницы: 11

Бренд: Yamaha Страницы: 92

Бренд: Ultraflex Страницы: 7

Бренд: TEL Страницы: 26

Бренд: Vimar Страницы: 32

Бренд: DAQ Страницы: 63

Бренд: HEIDENHAIN Страницы: 257

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

MP23xxxiec Series

Бренд: YASKAWA Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды