NSC Sicherheitstechnik Solution F2 Скачать руководство пользователя | Manualshive

Страница: 32 / 49

background image

NSC Sicherheitstechnik GmbH

32/47

2011 / 04 / 26

Eckendorfer Str. 125 c

Installation Manual Solution F2 20110509.doc

33609 Bielefeld

Version S031A01.01

Press save (F4) to save the new configuration

39

Modem

1. Call accept on
2. Call accept off
3. Initialisation
4. Hang up

Cancel                          OK

Modem functions

If there is mounted a telephone modem in the
FCP, from here you can send commands to the
modem. These commands are:

1. Call accept on

Will cause the modem to answer an
external phone call.

2. Call accept off

Disables the automatic call acceptance

3. Initialisation

Initializes the modem with an ATZ
command

4. Hang up

Disconnects modem from telephone
line.

By modem connection you can do the following
actions:

Read settings

Read eventmemory

Read diagnostic data

Online mode (Message display &
Operation)

but

NOT writing settings to FCP

41

Power Outputs
No.: ( old) Norm OC-Tol. Th.OC Th.SC
1 : (1008) 1000 + 100 = 1100 , 0738 Ohm
2 : (0995) 0995 + 100 = 1095 , 0734 Ohm
3 : (1283) 1282 + 100 = 1383 , 0882 Ohm
4 : (1375) 1374 + 100 = 1475 , 0974 Ohm

Cancel               Calib.       save

Power outputs: Thresholds

Here for the 4 monitored power outputs the thresholds
for open curcuit and short curcuit can be adjusted.
The thresholds depend on the load resistance of the
connected device inclusive the line resistance. This
total resistance can be ascertained automatically for
each power output individually by pressing Calib.(F3).
The software then automatically calculates the
thresholds for open curcuit and short curcuit.

In brackets you see the value of the last calibration
procedure, behind the 1st colon you see the actual
value and behind the second colon you see the
tolerance for each power output.
The toerance fort he thresholds can be changed in
the range 40 to 200

Ω

.

The resistance can also be measured with a
multimeter and typed in directly using the keyboard.

42

Loop parameters

Loop                       : 1
Open curcuit               : 999 Ohm
Short curcuit              : 100 mA
Number of detector LEDs    : 4

Cancel                            save

Loop parameters

In this menu the values for open curcuit and short
curcuit determined with the loopcalculation program
(Excel sheet) can be entered. Furthermore the
number of detector LEDs, that will be activated
simultanously on a loop, can be specified in the range
3-12. This input is important for the maximum alarm
current, which has influence on the maximum allowed
cable length and, as a consequence, to the
functionality of the system.

«
...
30
31
32
33
34
...
»

Содержание Solution F2


















































Отзывы:

Нет отзывов

Похожие инструкции для Solution F2

Бренд: Fairchild Страницы: 2

Бренд: Fagor Страницы: 103

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Racal Instruments Страницы: 94

Бренд: Racal Instruments Страницы: 97

Бренд: tau Страницы: 9

Бренд: tau Страницы: 8

Бренд: Balboa Water Group Страницы: 88

Бренд: ABB Страницы: 2

Бренд: Tamiya Страницы: 5

Бренд: Zencontrol Страницы: 2

Бренд: Daikin Страницы: 2

Бренд: Advantech Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды