Novexx ALX 924 Скачать руководство пользователя

Страница: 12 / 91

User Manual

ALX 92x

09/2016 | 00

Please note

Operating safety of the machine

Intended use



The machine must only be used in accordance with the specifications in section

Intended use



auf Seite 10.

Warning of injuries due to electrical shock

WARNING!

This unit operates at mains voltage! Contacting electrically live components can cause lethal
electrical shocks and burns.

The device is only completely disconnected from the mains if the power cable is unplugged.



Make sure the power supply socket is accessible.



In case of emergency, switch off the device and disconnect the power cable.

Installation:



Only operate the machine when the enclosure is properly installed.



The machine must only be connected by an authorised technician who is acquainted with the

associated dangers.



The machine must only be connected with other machines if they meet the requirements of a

SELV circuit (Safety Extra-Low Voltage circuit) in accordance with EN 60950.



Keep the machine's On/Off switch accessible.

Cleaning:



Before cleaning and maintenance, switch off the machine and pull out the main plug.



Keep the machine dry.



If a liquid gets into the machine, switch off the machine immediately and unplug the mains

contactor. Notify a service technician.

CAUTION!
If the supply voltage is too high or too low, the machine may be damaged.



Only operate the unit at the mains voltage given on the type plate.



Ensure that the mains voltage set on the machine corresponds to the local mains

voltage.

Содержание ALX 924




























































































Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды

Novexx ALX 924, Руководство пользователя

Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды