Novexx ALX 924 Скачать руководство пользователя страница 67

Страница: 67 / 91

User Manual

ALX 92x

09/2016 | 01

Startup and Operation

• With OD sensor (connected to USI)

Requirements:

– OD sensor is installed
–

DP INTERFACE > Material signal

= „On“

Depending on the machine setting, a warning signal or an error message appears:

A) Warning signal

With the setting

DP INTERFACE > Mat. signal stop

= „Off“, if the critical OD is reached, a warning

signal is activated at the USI, which can for example switch a signal lamp. The machine

doesn´t

stop.

B) Error message

With the setting

DP INTERFACE > Mat. signal stop

= „On“, if the critical OD is reached, an error signal

is activated at the USI. The machine stops and the following message appears:

• With OD sensor (connected to AI)

If the critical OD is reached, a warning signal is activated at the USI, which can for example
switch a signal lamp. The machine

doesn´t

stop.

Status num:

5123

USI Material low

Содержание ALX 924




























































































Результаты поиска

Содержание ALX 924

Отзывы:

Бренды по названию

Популярные бренды

Novexx ALX 924, Руководство пользователя

Результаты поиска

Содержание ALX 924

Отзывы:

Бренды по названию

Популярные бренды