Novexx ALX 924 Скачать руководство пользователя

Страница: 50 / 91

User Manual

ALX 92x

09/2016 | 01

Startup and Operation

Startup and Operation

ELECTRICAL CONNECTIONS

Connecting to the mains power supply

1. Ensure that the machine is switched off (mains power switch [33A] in position "O").
2. Connect the machine to a mains power socket [33C] using the provided power cable [33B].

[33] Connecting the ALX 92x. to a mains power socket.

WARNING!

This unit operates at mains voltage! Contacting electrically live components can cause lethal
electrical shocks and burns.



Make sure that the device is switched off before connecting the power cable.



Only operate the unit at the mains voltage given on the type plate.



Only connect the device to a grounded power socket fitted to authorised standards.



The power cable should be run to the device so that a) nobody will trip on it, and that b) the

power plug can easily be pulled out if necessary.



The maximum permitted length of the mains power connecting line is 3 m.



To disconnect the device completely, the power cable has to be pulled off.

Содержание ALX 924




























































































Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды

Novexx ALX 924, Руководство пользователя

Результаты поиска

Содержание ALX 924

Отзывы:

Похожие инструкции для ALX 924

Бренды по названию

Популярные бренды