Nortel 8300 Series страница 104 Скачать руководство пользователя | Manualshive

Страница: 104 / 220

background image

104

Chapter 4 SMP log error messages

316806-C

Message

Invalid Card Type fpr phyInit Slot <value>

Severity

WARNING

Description

This message indicates that an invalid card type has been detected.

Synopsis

N/A

Action

N/A

Message

Invalid configuration: network appears in two areas

Severity

INFO

Description

This message is generated when the same route appears for different areas.

Synopsis

Two areas have the same network.

Action

Configure the network properly so there is no repetition.

Message

invalid interface index

Severity

ERROR

Description

This message is generated when a VLAN ID is out of range. For example, if you
enable or disable IGMP for the circuit using an invalid VLAN, then this error
message occurs.

Synopsis

The VLAN interface being used is invalid.

Action

Provide a valid VLAN ID. Check the instructions in the VLAN configuration
command. If this error persists, then contact customer support for further
information.

Message

Invalid Port <value>

Severity

ERROR

Description

This message indicates that port translation failed.

Synopsis

N/A

Action

N/A

Message

invalid power supply configuration detected, PoE disabled and all PoE power
removed

Severity

ERROR

Description

This message indicates that mixed types of power supplies were installed in the
chassis.

Synopsis

PoE function disabled.

Action

Remove or replace power supplies to ensure that there are no mixed types of
power supplies installed.

«
...
102
103
104
105
106
...
»

Содержание 8300 Series





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8300 Series

Бренд: CAME Страницы: 19

Бренд: Vaisala Страницы: 32

ION 1200 Series

Бренд: PaloAlto Networks Страницы: 90

Бренд: VCS Страницы: 118

System Storage DS3200

Бренд: IBM Страницы: 2

Бренд: Teletronics International Страницы: 57

Бренд: YATO Страницы: 96

Бренд: ActionTec Страницы: 115

Бренд: TP-Link Страницы: 131

Бренд: KYLAND Technology Страницы: 24

Бренд: JLCooper Electronics Страницы: 12

Бренд: ADTRAN Страницы: 9

Бренд: Maestro Wireless Solution Страницы: 22

Бренд: Eaton Страницы: 32

Бренд: ZyXEL Communications Страницы: 12

Бренд: Cabletron Systems Страницы: 56

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card...

Бренд: 3Com Страницы: 6

StorageGRID Webscale SG5700 Series

Бренд: NetApp Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды