Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 7 / 201

background image

WARNING AND CAUTION

Read This Section Before Use!

CAUTION

The top of the tripod ferrule is very sharp and may injure your body.
Be careful in handling or carrying the tripod.

Check the shoulder strap and its clasp before carrying the tripod or
the instrument encased in the carrying case. Damaged strap or
imperfect clasping may cause an accident of falling.

Before setting up the tripod, check below to make sure no one’s
hands or feet are in the way. Failure to do so may result in injury if
hands or feet should be pierced by the legs of the tripod.

Fasten firmly the thumb screws of the tripod legs after mounting the
instrument on the tripod. If not, the tripod may collapse, resulting
in injury or instrument damage.

Be sure to fasten the clamp screw on the tripod securely after
installing the instrument on the tripod. Failure to do this may
cause the instrument to fall, resulting in injury or instrument
damage.

Fasten securely the leveling base clamp knob. If the knob is not
securely fastened, the leveling base may fall when you grasp the
carrying handle battery, resulting in injury or instrument damage.

Roughly moving the instrument by grasping the carrying handle
battery without first placing the battery mounting buttons in the
LOCK position may cause the main unit to come loose and fall,
resulting in injury or instrument damage. Make sure that the
battery pack is clamped securely in place and the mounting buttons
are set in the LOCK position.

Do not stack up the plastic carrying case and do not use it as a
stool. Plastic carrying case is slippery and unstable. Doing
things like this may cause an accident and result in personal injury
or instrument damage.

Do not swing or throw the plumb bob. It may hit and injure the
other person.

Be sure to read the instructions of Quick Charger Q-75U/E before
starting charging operation.

iii

«
...
5
6
7
8
9
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Bacharach Страницы: 64

Бренд: LaserLine Страницы: 24

Бренд: PASCO Страницы: 3

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: Keeler Страницы: 54

Бренд: Jenoptik Страницы: 54

Vortex Flow Industry

Бренд: Grundfos Страницы: 16

Бренд: Spacelabs Страницы: 156

Бренд: Omega Страницы: 4

Бренд: M-Audio Страницы: 21

Бренд: Kapro Страницы: 60

Бренд: ASD Страницы: 72

Бренд: Landtek Страницы: 3

Бренд: Selecta Страницы: 16

Бренд: Hanna Instruments Страницы: 16

Бренд: Major tech Страницы: 2

Бренд: Kurz Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды