Nikon DTM-502 Series Скачать руководство пользователя

Страница: 162 / 201

4. CHECKING AND ADJUSTMENT

4-1

CHECKING

AND

ADJU

TMEN

4-1. Plate

Level

(Making the axis of the level vial at right angle to the vertical axis of the
instrument)

1) Checking

(1) Set up the instrument on the tripod and follow the leveling procedures

described in [2-5. Leveling] p.2-10.

(2) Rotate the alidade 180°.

(3) Check to see if the bubble remains in the center of the vial. If a displacement

is detected it should be adjusted. Refer to the following adjustment
procedure.

2) Adjustment

(1) Using the adjusting pin supplied, rotate

the plate level’s adjustment screw to
move the bubble to eliminate half of
the displacement detected.

(2) Take up the remaining displacement

with leveling screw A (refer to the
Figure in p.2-10), centering the bubble.

(3) Recheck, and repeat if necessary.

Nikon

4-2. Circular

Level

1) Checking

After confirming the plate level is in
adjustment, check for any displacement of
the bubble’s centering in the circular level.
If it is out of adjustment, use the adjusting
pin to manipulate the three adjustment
screws, centering the bubble.

Содержание DTM-502 Series










































































































































































































Результаты поиска

Содержание DTM-502 Series

Отзывы:

Похожие инструкции для DTM-502 Series

Бренды по названию

Популярные бренды

Nikon DTM-502 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DTM-502 Series

Отзывы:

Похожие инструкции для DTM-502 Series

Бренды по названию

Популярные бренды