Nikon DTM-502 Series Скачать руководство пользователя

Страница: 5 / 201

Thank you for purchasing the Nikon products. This

instruction manual was written for the users of the

Electronic Total Station DTM-502 series. To ensure

correct usage read this manual carefully before

operating the instrument.

Also read the Instruction Manual provided with the

Battery Charger and any other equipments used

together with the DTM-502 series.

Warning and Caution

Symbols in This Manual

Though Nikon products are designed to provide you

utmost safety during use, incorrect usage or disregard of

the instructions can cause personal injury or property

damage. For your safety, read the instruction manual

carefully and thoroughly before usage. Do not discard

this manual but keep it near the product for easy

reference.

Inside this instruction manual, safety instructions are

indicated with the symbols shown below. Be sure to

follow the instructions marked with these symbols for

your safety.

WARNING

Disregarding instructions marked with this symbol

may lead to death or serious injury.

CAUTION

Disregarding instructions marked with this symbol

may lead to injury or property damage.

Содержание DTM-502 Series










































































































































































































Результаты поиска

Содержание DTM-502 Series

Отзывы:

Похожие инструкции для DTM-502 Series

Бренды по названию

Популярные бренды

Nikon DTM-502 Series, Инструкция по эксплуатации

Результаты поиска

Содержание DTM-502 Series

Отзывы:

Похожие инструкции для DTM-502 Series

Бренды по названию

Популярные бренды