Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 81 / 201

background image

3

PR

G

:

1. 2Pt

Re

f

JKL

PRG

4

4) Program Key

1. 2-Pt Reference Line
Measuring Distance and Offset Values along a Specified Line

Press the [1] key on the Programs menu.

Input the first point for the reference line.
Inputting the point by measurement is also available.
Press the [MSR] softkey to get to the observation
screens.

Direct Measurement screen

•

By pressing the [MSR] softkey, a direct

measurement screen is shown.
Sight the target and press [MSR1] or [MSR2]. After
taking a measurement, it automatically proceeds to
the “Record PT” screen.

•

If [ESC] is pressed on the “Record PT” screen, the

measured point will be used but not recorded in the
job.

Input the second point for the reference line.

When the asterisk(*) is used in the PT field, a list of
points found is shown. Select a point and press the
[ENT] key.

3-55

«
...
79
80
81
82
83
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Keithley Страницы: 49

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: Omicron Страницы: 80

Бренд: OHAUS Страницы: 52

Бренд: Yamaha Страницы: 14

Disklavier Mark II XG Series

Бренд: Yamaha Страницы: 12

Comark Diligence 600

Бренд: Fluke Страницы: 61

KINGFISHER PLUS+

Бренд: semaphore Страницы: 247

Бренд: C.R. Laurence Страницы: 4

Бренд: Neogen Страницы: 9

Бренд: Fora Страницы: 64

Бренд: Lutron Electronics Страницы: 23

Бренд: Kirby Morgan Страницы: 101

Бренд: BASI Страницы: 69

AUER Atemluft 300 bar

Бренд: MSA Страницы: 52

Бренд: Pilot Communications Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды