Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 98 / 201

background image

2. Angle-Offset Measurements

After (or before) a distance measurement, press the
[O/S] and [2] to enter the Angle- offset function.

3

O/S:

2. Angl

e

When no distance measurement is taken before
entering the Angle-offset, a temporary measurement
screen is displayed.
Sight the target and press the [MSR1] or [MSR2].

Rotate the alidade and telescope to take a necessary
angle offset while the measured distance (HD)
remains unchanged.
Press the [ENT] key or [OK] softkey to record the
offset point.
The XYZ data will also be recalculated based on the
new angle.

•

It is also possible to record an angle offset on the BMS.

After a distance measurement is taken the alidade and/or telescope can be rotated.
Then press [ENT] to record the measured distance with the updated angle value. In
this situation the dimension of the angle offset will not be stored as a CO record. To
store the CO record, the O/S function should be used.

3-72

«
...
96
97
98
99
100
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Kane Страницы: 19

Бренд: Bante Instruments Страницы: 6

Бренд: ColorLite Страницы: 68

Бренд: Keysight Страницы: 92

Бренд: ESP Страницы: 12

Бренд: Seben Страницы: 16

Бренд: U.S. Solid Страницы: 30

OMCL-AC240TS-R3

Бренд: Olympus Страницы: 3

Бренд: BERG Страницы: 23

PMD Analyzer 5500B

Бренд: EXFO Страницы: 4

In-Situ Rugged TROLL 100

Бренд: Geotech Страницы: 6

PowerMaster MTA15Z

Бренд: PowerMetrix Страницы: 13

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Бренд: Gait up Страницы: 17

Бренд: Apera Instruments Страницы: 30

Бренд: Keysight Страницы: 896

Бренд: gaskatel Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды