Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 31 / 201

background image

3

2) LCD Backlight, Reticle, LG, Sound and Contrast

[ ]/[ ]

<4-switch window> <Contrast adjustment>

The LCD backlight can be turned ON/OFF by pressing the illumination key (       ).
Holding down the illumination key for one second opens a small window (4-switch
window) on any screen. The window includes Backlight, Reticle, Lumi-guide and
Sound ON/OFF switches as well as Contrast adjustment.

On the 4-switch window, press the [ENT] key or [1] to [4] to turn the switch
ON/OFF.  The Up/Down arrow keys move the cursor among the four switches.
The Right/Left arrow keys change the window between 4-switch and the Contrast
adjustment screen.  On the Contrast adjustment screen, use Up/ Down arrow keys to
change the contrast.
Press the [ESC] key to close the window.

1. Backlight

: Backlight OFF

: Backlight ON

2. Reticle

: Reticle light OFF

: Reticle light ON (minimum)

: Reticle light ON (medium)

: Reticle light ON (maximum)

3-5

«
...
29
30
31
32
33
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 16

Бренд: Nagano Keiki Страницы: 25

MTEK6000 Series

Бренд: Metretek Страницы: 81

Бренд: Keysight Страницы: 66

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Rodstation Страницы: 28

QI-POWER-485-300

Бренд: QEED Страницы: 2

Duomat Evolution DeLuxe

Бренд: Dennerle Страницы: 27

Бренд: Seaward Страницы: 2

Commissioner dali

Бренд: Artistic License Страницы: 26

Бренд: Hanna Instruments Страницы: 2

Бренд: Dewetron Страницы: 48

WaveRunner 8000-R

Бренд: Teledyne Lecroy Страницы: 20

Бренд: Keithley Страницы: 350

Vigilant Plant EXA TB Series

Бренд: YOKOGAWA Страницы: 140

Бренд: Patlite Страницы: 21

Бренд: B&B Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды