Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 11 / 201

background image

2

PR

EP

AR

A

T

ION

2-2. Recharging and Connecting the BC-80

WARNING

Use only the specified charger Q-75U/E for charging the battery pack
BC-80. Charging by the other types of chargers than specified may
cause fire or rupture. (BC-80 can not be charged by using the
charger Q-7U/E or Q-7C.)

While recharging the battery pack, do not cover the charger with any
blanket or clothing which can cause overheating. Make sure the
charger is able to dissipate heat adequately.

Avoid recharging in humid or dusty places, in direct sunlight, and near
heaters. Do not recharge when wet. Doing so may cause electric
shock, overheating or fire.

Although the battery pack BC-80 is equipped with an auto-reset circuit
breaker, care should be taken not to short the contacts. Shorting may
cause fire or burn.

Never burn or heat the battery. Doing so may cause rupture or injury.

When storing the battery pack or charger, guard against a short circuit
by putting the insulating tape on the contact point or by doing some
other methods. Failure to do so may result in a short circuit, causing
a fire, burn or instrument damage.

CAUTION

Be sure to read the instructions of Quick Charger Q-75U/E before
starting charging operation.

Roughly moving the instrument by grasping the carrying handle battery
without first placing the battery mounting buttons in the LOCK position
may cause the main unit to come loose and fall, resulting in injury or
instrument damage. Make sure that the battery pack is clamped
securely in place and the mounting buttons are set in the LOCK
position.

2-2

«
...
9
10
11
12
13
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: Parr Instrument Company Страницы: 130

Бренд: jenway Страницы: 17

Бренд: WAGER Страницы: 36

Бренд: Kane Страницы: 16

Бренд: Bacharach Страницы: 48

Бренд: Bacharach Страницы: 24

Бренд: Macnaught Страницы: 14

Бренд: Narvitech Страницы: 2

Бренд: Olympus Страницы: 4

Бренд: YOKOGAWA Страницы: 2

ADMAG TI Series

Бренд: YOKOGAWA Страницы: 8

Бренд: E Instruments Страницы: 144

Бренд: Conrad Electronic Страницы: 38

Бренд: H. HERMANN EHLERS Страницы: 40

Бренд: X-Rite Страницы: 130

Бренд: TE Connectivity Страницы: 3

Rangemaster CRF 1000

Бренд: Leica Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды