Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 140 / 201

background image

4-3-3. Edit Station record

The system will not recalculate all measurements based on the
change in Station. All Coordinate and RAW data observed from
edited ST must be recalculated in your post-processing software.

3

MENU:

4. Data

If you need to modify the ST record, place the
cursor on the ST you are to change.
Press the white key beneath the [Edit] softkey.

All items in the ST record can be edited but no
recalculation will be performed on the instrument.
Press [ENT] in the last field (AZ) to confirm the
change.

•

Even if the STN point and/or Height of Instrument is changed, coordinate of the

observation points are not re-calculated on the instrument. Only a comment record
to indicate the change is to be recorded.

Ex.) CO,HI changed at ST:9012 Old HI= 1.3456m

•

Also, the RAW records are not re-calculated when BS point and/or BS Azimuth is

changed. Only a CO record is to be stored.

4-4. Search Record

You can search for records by their type, point number/name, code, or by any
combination of those.

4-4-1. Search from RAW record

Press the [Srch] softkey to activate the RAW data
search function.

3-114

«
...
138
139
140
141
142
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Parker Research Corp Страницы: 3

Бренд: GE Страницы: 8

Moisture Image 1 Series

Бренд: GE Страницы: 110

DigitalFlow GS868

Бренд: GE Страницы: 74

DigitalFlow GS868

Бренд: GE Страницы: 81

Бренд: Baker Hughes Страницы: 59

Бренд: Baker Hughes Страницы: 2

Бренд: Panametrics Страницы: 67

Бренд: Panametrics Страницы: 108

Transport PT878

Бренд: GE Страницы: 97

BML SL1-ALZ-ZZ Series

Бренд: Balluff Страницы: 26

Бренд: Quantel Страницы: 2

Бренд: VeEX Страницы: 842

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 4

Бренд: Velleman Страницы: 8

Бренд: velocomp Страницы: 4

Бренд: MULTISPAN Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды