Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 70 / 201

background image

3

ST

N

4. Remote Benchmark (RBM)
Determine Station Elevation

Press the [4] key on STN menu.

Input the BM point and press the [ENT] key. When
the point is found, it is displayed for a while and the
cursor moves to the HT field. Type HT and press
the [ENT] key.

Sight the BM point and press the [MSR1] or
[MSR2] key.

F1/F2 measurement is also available by pressing the
[F2] softkey or just flipping the telescope to Face2
after a distance measurement.

[ENT]

Updated station coordinate is displayed. The HI can
be changed on this screen.
Press the [ENT] key to record the updated STN.

•

When the HI is changed, the Z-coordinate will be updated before recording the
station.

•

A station setup must be completed before the Remote Benchmark function is used.

3-44

«
...
68
69
70
71
72
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Icare Страницы: 3

Бренд: Sensia Страницы: 16

Бренд: Vaisala Страницы: 90

Бренд: Vaisala Страницы: 4

Бренд: DAKOTA ULTRASONICS Страницы: 50

Бренд: Jamar Страницы: 4

Бренд: Danfoss Страницы: 4

Бренд: Schneeberger Страницы: 35

Бренд: Kobold Страницы: 55

Бренд: Clavitech Страницы: 56

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Бренд: Hanna Instruments Страницы: 12

Бренд: UEi Страницы: 5

Бренд: Anglerfish Creative Lighting Страницы: 15

Бренд: Agilent Technologies Страницы: 20

Бренд: Stabila Страницы: 14

Бренд: ASD Страницы: 72

Бренд: Perel Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды