Nikon DTM-502 Series Скачать руководство пользователя | Manualshive

Страница: 59 / 201

background image

3

ANG

3. Rept.
Recording a Foresight Point after Repeat Angle Measurement

Press the [4] key to activate and the repeat angle
measurement. “HR=0” is shown.

Sight the Backsight and press the [ENT] key.

Sight the foresight and press the [ENT] key. The
horizontal angle is accumulated and the value is
held again.
To terminate the repeat angle measurement, press
the [ESC] key.

After you accumulate enough horizontal angle
between the Backsight and Foresight, take a
measurement to the Foresight by [MSR1] or
[MSR2].
Averaged horizontal angle is displayed and fixed
until the process is finished or cancelled.

HRx = HR

Σ

÷

N

HA = BSAz + HRx (normalized)

HRx will not be updated even if the instrument is
moved.

Press the [ENT] key to store the Foresight as a CP
record. Check PT/HT/CD and press the [ENT] key
to record.

•

In the repeat angle measurement, “HA:” header is replaced by “HR

Σ

” and the

number of repeat angles is displayed on top of the screen (N=5 etc).

•

Horizontal angles can be measured up to 1999º59’59”5.

•

This function will store both RAW and XYZ data (as CP record) regardless of the
“Store DB” setting.

3-33

«
...
57
58
59
60
61
...
»

Содержание DTM-502 Series










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DTM-502 Series

Бренд: Kane Страницы: 12

Бренд: Medeli Страницы: 14

System SourceMeter 2601B

Бренд: Keithley Страницы: 13

Бренд: Keller-druck Страницы: 8

Бренд: PAT Страницы: 57

Clavinova CLP-110

Бренд: Yamaha Страницы: 46

Clavinova CLP-110

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 8

Бренд: E Instruments Страницы: 2

Бренд: Mini Страницы: 20

Бренд: Divertug Страницы: 47

Бренд: HyQuest Solutions Страницы: 25

Бренд: M-Audio Страницы: 21

Бренд: Allen Organ Company Страницы: 29

Бренд: Biobase Страницы: 36

Roast Alert/3 ET-8C

Бренд: Redi-Chek Страницы: 3

AquaShock 850046K

Бренд: Sper scientific Страницы: 28

Бренд: INTERSPIRO Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды