background image

15

Installation and quick start commissioning guide - Commander ID300/302

5511 en - 2017.06 / a

MECHANICAL INSTALLATION

Type

Option

Name

Details

I/O expansion

ID-SIZE1-I/O

• For size 1 and 2 drives, use ID-SIZE1-I/O

Increases the I/O capability
Mounting arrangement: replaces standard terminal 

cover (new drive dimensions: H + 41.5 mm). This option 

has to be mounted by the user. Please refer to the 

relevant mounting documentation. A fieldbus option 

cannot be fitted at the same time.

SI-I/O module

• For size 3 drive: fieldbus module.

Increases the I/O capability

Mounting arrangement: This option has to be fitted to 

the option slot and connected by the user. Please refer 

to the relevant mounting documentation. A fieldbus 

option cannot be fitted at the same time.

Brake

control

ID-SIZE1-

Brake 

Contactor

ID-SIZE3-

Brake 

Contactor

• For size 1 and 2 drives, use ID-SIZE1-Brake 

Contactor 

• For size 3 drive, use ID-SIZE3-Brake Contactor 
Mounting arrangements: factory-fitted inside the drive

Allows the drive to easily control a motor with FFB 

brake by using a dedicated drive preset configuration 

(“AV with brake” or “3PS/1Ana brake”). For connection 

details, see section 3.5.

External 

EMC filter

ID-SIZE1-EMC 

filter LV-LL or 

HV-LL

ID-SIZE3-EMC 

Filter HV-LL

Allows the drive to conform to C1 level according to 

EN61800-3 + A1 (2012) (available soon)

2 - MECHANICAL INSTALLATION

 The mechanical and electrical installation 

instructions must be adhered to. Any 

questions or doubt should be referred to 

the supplier of the equipment. It is the 

responsibility of the owner or user to ensure that 

the installation of the Commander ID300/302 and 

any external option unit, and the way in which they 

are operated and maintained, comply with the 

applicable legislation and regulations and codes of 

practice in the country in which the equipment is 

used.

  •

 The drive contains capacitors that remain 

charged to a potentially lethal voltage after the AC 

supply has been disconnected. If the drive has 

been energized, the AC supply must be isolated 

at least 10 minutes before work may continue. 

Normally, the capacitors are discharged by an 

internal resistor. Under certain, unusual fault 

conditions, it is possible that the capacitors may 

fail to discharge, or be prevented from being 

discharged by a voltage applied to the output 

terminals. If the drive has failed in a manner that 

causes the keypad display (if present) to go blank 

immediately, it is possible the capacitors will not be 

discharged. In this case, consult Leroy-Somer or 

an authorized distributor.

  •

 The Commander ID300/302 and its options must 

be installed by professional assemblers who are 

fami liar with the requirements for safety and EMC. 

The assembler is responsible for ensuring that 

the end product or system complies with all the 

relevant laws in the country where it is to be used.

  •

 When the cover is open, the 

Commander ID300/302 degree of protection 

is IP10. Any work should only be carried out 

by experienced, qualified personnel. The 

Commander ID300/302 must not be opened whilst 

energized.

  •

 Holes are provided at the lowest points of the 

enclosure, depending on the operating position, 

to drain off any moisture that may have been 

accumulated inside during cooling of the machine. 

In conditions which encourage the formation of 

condensation, it is advisable to leave the drain 

holes permanently open.

2.1 - Checks on receipt

Before installing the Commander ID300/302, check 

that:

- The motor and drive have not been damaged during 

transport,

- The information on the nameplates is compatible with 

the power supply.

For nameplate details, please refer to section 1.2.

Содержание LEROY-SOMER Commander ID30 Series









































Отзывы: