Nice MC824HR, Инструкции и предупреждения по установке и использованию

Страница: 25 / 28

ENGLISH – 25
&
&
INSTRUCTIONS AND WARNINGS FOR THE USER
Before using the automation for the first time, ask the installer to
explain the origin of any residual risks and take a few minutes
to read this instruction manual and warnings for the user given
to you by the installer. Store the manual for future reference and
hand it to the new owner when transferring the automation.
a
WARNING!
Your automation is a machine that faithfully executes
commands imparted by the user. Negligence and
improper use may lead to dangerous situations:
– do not manoeuvre the gate if there are people, animals
or objects within its range of operation
– it is strictly forbidden to touch parts of the automation
while the gate or door is moving
– the photocells are not a safety device but only an
auxiliary aid to safety. They are built using highly reliable
technology but, in extreme conditions, may malfunction
or even become defective. In certain cases, the defect
may not be clearly evident. For these reasons, it is
important to follow all the instructions given in this
manual when using the automation
– periodically check that the photocells work properly.
a
IT IS STRICTLY FORBIDDEN to transit through the
gate while it is closing! It is only possible to transit
through the gate when it is fully open and the leaves
are at a standstill.
a
CHILDREN
An automation system guarantees a high degree
of safety. With its detection systems, it can control
and guarantee the gate’s movement in the presence
of people or objects. It is nonetheless advisable to
forbid children from playing near the automation
and not to leave remote controls near them to
prevent any unwanted activation of the system. The
automation is not a toy!
The product is not intended for use by persons,
including children, with limited physical, sensory
or mental capacities, or who lack experience or
knowledge, unless supervised or trained in the use
of the product by a person responsible for their
safety.
Anomalies: if the automation appears to behave strangely,
disconnect the power supply to the automation and manually
unlock the motor (consult the respective instruction manual)
to manoeuvre the gate manually. Do not perform any repairs
personally, but contact your trusted installer.
l
Do not modify the system or the programming
and adjustment parameters of the control unit:
your installer is exclusively responsible for these
operations.
Failure or power outage: while waiting for your installer to
intervene or the power supply to be restored, if the system is not
equipped with back-up batteries, the automation can be used
by manually unlocking the motor (consult the relative instruction
manual) and manually moving the gate leaf.
Safety devices out of order: the automation can also be used
when one or more safety devices are defective or out of order.
The gate can be operated in the “ hold-to-run ” mode in the
following way:
1. send a command to operate the gate, with a transmitter or
key selector, etc. If everything works properly, the gate will
move normally, otherwise proceed as described below
2. within 3 seconds, press the control again and hold it down
3. after roughly 2 seconds, the gate will move in the “ hold-
to-run ” mode, in other words, it will continue moving so
long as the control is held down.
m
If the safety devices are out of order, have the
system repaired as soon as possible by a qualified
technician.
The test, periodic maintenance and any repairs must be
documented by the person carrying out the work and the
documents must be stored by the owner of the automation. The
only interventions the user may carry out periodically include
cleaning of the photocell glass components (use a soft and
slightly damp cloth) and removing any leaves or stones that may
obstruct the automation.
m
The user of the automation must manually unlock
the motor before starting any maintenance
operation, to prevent other people from accidentally
manoeuvring the gate (consult the respective
instruction manual).
Maintenance: in order to ensure constant levels of safety and
the longest useful life for the automation, routine maintenance
must be carried out (at least every 6 months).
l
Only qualified personnel is authorised to carry out
checks, maintenance operations and repairs.
Disposal: at the end of its useful life, the automation must be
dismantled by qualified personnel and the materials must be
recycled or disposed of in compliance with the local regulations
in force.
l
If the automation was locked using the “Lock
automation” command, the gate will not move when
a command is sent and the warning light will emit 9
short flashes.