Nice Hansa Robus 250, Инструкции и предупреждения по установке и использованию

Страница: 23 / 28

English – 23
8) Technical characteristics
Nice S.p.a., in order to improve its products, reserves the right to modify their technical characteristics at any time without prior notice. In any
case, the manufacturer guarantees their functionality and fitness for the intended purposes.
All the technical characteristics refer to an ambient temperature of 20°C (±5°C)
Use in acid, saline or potentially explosive
atmosphere
330 x 195 x 277 h; 8 kg 330 x 210 x 303 h; 11 kg
Type
Model
Technical characteristics: NiceHansa Robus
Electromechanical gearmotor for the automatic movement of sliding gates for residential
use, complete with electronic control unit
RB250 RB500
Pinion
Z: 15; Module: 4; Z: 18; Module: 4;
Pitch: 12.6 mm; Gear diameter: 60 mm Pitch: 12.6 mm; Gear diameter: 72 mm
Peak thrust
[corresponding to the ability to develop a
force capable of moving the leaf]
9,3 Nm 13 Nm
[310 N] [360 N]
Nominal torque
[corresponding to the ability to develop a force
capable of maintaining the movement of the leaf]
3,9 Nm 5,8 Nm
[130 N] [160 N]
Speed at nominal torque 20 m/min
Idling speed (the control unit allows 6 speeds to
be programmed, approx. equal to: 100, 85, 70,
55, 45, 30%) 70, 55, 45, 30%)
22 m/min 24 m/min
Maximun rating of operating cycles
(nominal torque) 400 cycles/day 450 cycles/day
(the control unit allows up to the maximum described in tables 2 and 3)
Maximum continuous operating time
(nominal torque) 7 minutes
(the control unit limits the continuous operation up to the maximum described in tables 2 and 3)
Operating limits
In general, NiceHansa Robus is suitable for the automation of gates featuring weights or
lengths as shown in Tables 2, 3 and 4
Durability Estimated between 20,000 and 250,000 cycles, following the conditions indicated in table 4
Thrust maximum absorbed power
[equivalent to amperes]
430 W [2,1 A] 450 W [2,2A]
Insulation class 1 (a safety grounding system is required)
Emergency power supply With PS124 optional accessory allows up to 20 operations in case of power failure
Flashing light output For 2 LUCYB flashing lights (12V, 21 W lamp)
BLUEBUS Output One output with a maximum load of 15 BlueBus units
Open Gate Indicator Output
for one 24V maximum 4W bulb (the output voltage may vary between –30 and +50% and
can also control small relays)
STOP input
For normally open contacts, for 8,2K Ω ; constant resistance, or normally closed contacts; with self-
recognition (any variation from the memorized status causes the “STOP” command)
Step-by-step Input For normally open contacts (the closing of the contact causes the “STEP-BY-STEP” command)
OPEN input
CLOSE input For normally open contacts (the closing of the contact causes the “OPEN” command)
For normally open contacts (the closing of the contact causes the “CLOSE” command)
Radio connector “SM” connector for SMXI receivers
Radio AERIAL Input 52 Ω for RG58 or similar type of cable
RB 250 - RB500 power supply 230 Vac (+10% -15%) 50/60Hz.
Programmable functions 8 ON-OFF functions and 8 adjustable functions (see tables 7 and 9)
Operating temperature -20°C ÷ 50°C
No
Protection class IP 44
Dimensions and weight
Self-Recognition functions
Self-recognition of the type of “STOP” device (Normally Open, Normally Closed contact or
8,2K Ω ) Self-recognition of the gate length and calculation of the deceleration points and the
partial opening point.