manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 9

Contents

NI PXI-4220 User Manual

viii

ni.com

Glossary

Index

Figures

Figure 2-1.

NI PXI-4220 Front Label...................................................................... 2-2

Figure 2-2.

PXI-4220 Front Connector and General Circuit Diagram .................... 2-3

Figure 2-3.

Socketed Resistor Locations ................................................................. 2-4

Figure 2-4.

Quarter-Bridge I Circuit Diagram......................................................... 2-5

Figure 2-5.

Quarter-Bridge II Circuit Diagram ....................................................... 2-6

Figure 2-6.

Half-Bridge Type I Circuit Diagram..................................................... 2-7

Figure 2-7.

Half-Bridge Type II Circuit Diagram ................................................... 2-8

Figure 2-8.

Full-Bridge Type I Circuit Diagram ..................................................... 2-9

Figure 2-9.

Full-Bridge Type II Circuit Diagram .................................................... 2-10

Figure 2-10.

Full-Bridge Type III Circuit Diagram................................................... 2-11

Figure 2-11.

Remote Sense Circuit Diagram............................................................. 2-12

Figure 4-1.

Basic Wheatstone Bridge Circuit Diagram........................................... 4-1

Figure 4-2.

Quarter-Bridge Type I Measuring Axial and Bending Strain............... 4-4

Figure 4-3.

Quarter-Bridge Type I Circuit Diagram ............................................... 4-4

Figure 4-4.

Quarter-Bridge Type II Measuring Axial and Bending Strain ............. 4-6

Figure 4-5.

Quarter-Bridge Type II Circuit Diagram .............................................. 4-7

Figure 4-6.

Half-Bridge Type I Measuring Axial and Bending Strain.................... 4-8

Figure 4-7.

Half-Bridge Type I Circuit Diagram..................................................... 4-9

Figure 4-8.

Half-Bridge Type II Rejecting Axial and 
Measuring Bending Strain .................................................................... 4-10

Figure 4-9.

Half-Bridge Type II Circuit Diagram ................................................... 4-11

Figure 4-10.

Full-Bridge Type I Rejecting Axial and Measuring Bending Strain .... 4-12

Figure 4-11.

Full-Bridge Type I Circuit Diagram ..................................................... 4-13

Figure 4-12.

Full-Bridge Type II Rejecting Axial and Measuring Bending Strain... 4-14

Figure 4-13.

Full-Bridge Type II Circuit Diagram .................................................... 4-15

Figure 4-14.

Full-Bridge Type III Measuring Axial and 
Rejecting Bending Strain ...................................................................... 4-17

Figure 4-15.

Full-Bridge Type III Circuit Diagram................................................... 4-17

Figure 4-16.

Block Diagram of the NI PXI-4220...................................................... 4-19

Figure 4-17.

Signal During Simultaneous Sample and Hold Sampling .................... 4-29

Figure 4-18.

AI CONV CLK Signal Routing ............................................................ 4-32

Figure 4-19.

NI PXI-4220 PXI Trigger Bus Signal Connection ............................... 4-34

Figure 5-1.

Typical Program Flowchart .................................................................. 5-2

Figure 5-2.

LabVIEW Channel Property Node with Filtering Enabled at 
10 kHz and SS/H Disabled ................................................................... 5-11

Figure 5-3.

General Synchronizing Flowchart ........................................................ 5-13

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды