manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 7

Contents

NI PXI-4220 User Manual

vi

ni.com

Verifying the Signal ...................................................................................................... 3-8

Verifying the Signal in NI-DAQmx Using a Task or Global Channel ........... 3-8

Chapter 4
Theory of Operation

Strain Gauge Theory...................................................................................................... 4-1

Wheatstone Bridges ........................................................................................ 4-1
Strain Gauges .................................................................................................. 4-2
Acronyms, Formulas, and Variable Definitions ............................................. 4-2
Software Scaling and Equations ..................................................................... 4-3
Quarter-Bridge Type I..................................................................................... 4-4
Quarter-Bridge Type II ................................................................................... 4-6
Half-Bridge Type I.......................................................................................... 4-8
Half-Bridge Type II ........................................................................................ 4-10
Full-Bridge Type I .......................................................................................... 4-12
Full-Bridge Type II ......................................................................................... 4-14
Full-Bridge Type III........................................................................................ 4-16

NI PXI-4220 Theory of Operation ................................................................................ 4-18

Bridge Configuration and Completion............................................................ 4-21
Excitation ........................................................................................................ 4-21

Remote Sense ................................................................................... 4-22

Gain/Input Range ............................................................................................ 4-24
Filter ................................................................................................................ 4-25
Offset Null Compensation .............................................................................. 4-26
Shunt Calibration ............................................................................................ 4-27
Simultaneous Sample and Hold ...................................................................... 4-28

Maximum Acquisition Rate.............................................................. 4-30

Measurement Considerations .......................................................................... 4-30

Differential Signals........................................................................... 4-30
Common-Mode Rejection Ratio....................................................... 4-30
Effective CMR.................................................................................. 4-31

Timing and Control Functional Overview ...................................................... 4-31
Programmable Function Inputs ....................................................................... 4-32
Device and PXI Clocks ................................................................................... 4-33

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды