manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 62

Chapter 4

Theory of Operation

©

 National Instruments Corporation

4-27

NI PXI-4220 User Manual

Refer to the 

Configurable Settings in MAX

 section of Chapter 3, 

Configuring and Testing

, for more information about programmatically 

performing offset null compensation in MAX. For more information about 
programmatically performing offset null compensation in NI-DAQmx, 
refer to the 

Developing Your Application in NI-DAQmx

 section of 

Chapter 5, 

Developing Your Application

.

Shunt Calibration

Shunt calibration is a process used to obtain a gain adjust factor, which is 
used to correct for system gain error and discrepancies between nominal 
gauge factor and actual gauge factor of the strain gauge.

The gain adjust factor is derived using theoretical (simulated) signal levels 
that should result from engaging a shunt resistor across one leg of a bridge 
sensor, and the measured signal levels with the shunt resistor actually 
engaged.

Use the following formula to calculate the gain adjust factor:

The gain adjust factor is then multiplied by each future measurement to 
obtain highly accurate measurements that are adjusted for any gain errors 
or discrepancies in the nominal gauge factor. Refer to the 

Configurable 

Settings in MAX

 section of Chapter 3, 

Configuring and Testing

, for more 

information about performing shunt calibration automatically in global 
channels using NI-DAQmx in MAX. For more information about 
programmatically performing shunt calibration in NI-DAQmx, refer to 
the

Developing Your Application in NI-DAQmx

 section of Chapter 5, 

Developing Your Application

.

The NI PXI-4220 has two independent shunt calibration circuits 
available for each channel at pins SCA (pin 4), QTR/SCB (pin 9), and 
SCCOM (pin 5) on the D-SUB connectors. Each shunt calibration circuit 
consists of a resistor in series with a switch. The NI PXI-4220 shunt 
calibration switch is a long-life solid-state switch. The electronic switch 
is galvanically isolated from ground; therefore, you can connect shunt 
calibration resistor A to any external bridge element.

Gain Adjust Factor

simulated signal level

measured signal level with shunt resistor engaged

------------------------------------------------------------------------------------------------------------------------

=

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды