NI PXI-4220 Скачать руководство пользователя страница 26

Страница: 26 / 125

Chapter 2

Connecting Signals

NI PXI-4220 User Manual

2-12

ni.com

Remote Sense

For remote sensing, wire the NI PXI-4220 for remote sense as shown in
Figure 2-11. Refer to the

Remote Sense

section of Chapter 4,

Theory of

Operation

, for more information about remote sensing. Using remote sense

with the NI PXI-4220 is recommended to properly regulate the excitation
voltage,

, being applied to the sensor.

Figure 2-11.

Remote Sense Circuit Diagram

The following symbols apply to the circuit diagram and equations:

•

, R

, and R

are the transducer bridge elements.

•

is the measured voltage.

•

is the excitation voltage.

•

is the lead resistance.

•

RSENSE

is the measured bridge excitation.

Note

Remote sense is illustrated using a full-bridge circuit diagram for simplicity, but in

general, the

RSENSE

terminals should be connected to your transducer at the points that

supply

. For example, connect RS

+ (pin 3) to P

+ (pin 2), and RS

– (pin 8) to

– (pin 7) at the sensor.

–

NI PXI-4220

Transducer

S+ (Pin 1)

S– (Pin 6)

P+ (Pin 2)

P– (Pin 7)

RS+ (Pin 3)

RS– (Pin 8)

RSENSE

–

Remote
Sense
Feedback
Loop

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Результаты поиска

Содержание PXI-4220

Отзывы:

Бренды по названию

Популярные бренды

NI PXI-4220, Руководство пользователя

Результаты поиска

Содержание PXI-4220

Отзывы:

Бренды по названию

Популярные бренды