manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 11

©

 National Instruments Corporation

1-1

NI PXI-4220 User Manual

1

About the NI PXI-4220

This chapter provides an introduction to the NI PXI-4220 device and 
its installation.

The NI PXI-4220 is part of the SC Series of data acquisition (DAQ) devices 
with integrated signal conditioning. The SC Series reduces measurement 
setup and configuration complexity by integrating signal conditioning and 
DAQ on the same product.

The NI PXI-4220 is a full-featured dynamic strain device with 
programmable bridge-sensor signal conditioning, programmable filter, and 
programmable gain settings per channel ensuring maximum accuracy for 
bridge sensors. The NI PXI-4220 features the National Instruments (NI) 
programmable gain amplifier (PGA), an instrumentation-class amplifier that 
guarantees fast settling times at all gain settings. The NI PXI-4220 also uses 
the NI-DAQmx DAQ Assistant, specifically the 

Strain Gage Calibration

 

wizard, to easily perform offset null compensation and shunt calibration.

The NI PXI-4220 is a two-channel module for interfacing to Wheatstone 
bridge configurations. The NI PXI-4220 has the following features:

•

Two differential analog input (AI) channels

•

16-bit resolution

•

333 kS/s single-channel sampling rate

•

66 kS/s per channel when simultaneously sampling

•

Direct connectivity through two male D-Subminiature (D-SUB) 
connectors

•

Instrumentation amplifier per channel

•

Simultaneous sample-and-hold (SS/H) capability using track-and-hold 
(T/H) circuitry

•

Synchronization with other DAQ devices through the PXI trigger bus

•

4-pole software programmable Butterworth filters with software 
selectable filter settings of bypass (no filtering), 10 Hz, 100 Hz, 1 kHz, 
and 10 kHz per channel

•

Programmable voltage excitation with remote sense per channel

•

Programmatic offset null compensation per channel

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды