manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 6

©

 National Instruments Corporation

v

NI PXI-4220 User Manual

Contents

Chapter 1
About the NI PXI-4220

What You Need to Get Started ......................................................................................1-2
National Instruments Documentation ............................................................................1-3
Installing the Application Software, NI-DAQ, and the DAQ Device ...........................1-3
Installing the NI PXI-4220 ............................................................................................1-4
LED Pattern Descriptions ..............................................................................................1-4

Chapter 2
Connecting Signals

Connecting Bridge Sensor Signals to the NI PXI-4220 ................................................2-1

Quarter-Bridge Type I .....................................................................................2-4
Quarter-Bridge Type II....................................................................................2-6
Half-Bridge Type I ..........................................................................................2-7
Half-Bridge Type II.........................................................................................2-8
Full-Bridge Type I...........................................................................................2-9
Full-Bridge Type II..........................................................................................2-10
Full-Bridge Type III ........................................................................................2-11
Remote Sense ..................................................................................................2-12

Chapter 3
Configuring and Testing

Verifying and Self-Testing Using Device Test Panels ..................................................3-1
NI PXI-4220 Software-Configurable Settings...............................................................3-2

Common Software-Configurable Settings ......................................................3-2

Bridge Configuration and Completion..............................................3-2
Excitation Level ................................................................................3-2
Filter ..................................................................................................3-3
Gain/Input Range ..............................................................................3-3
Offset Null Compensation Potentiometers .......................................3-3
Shunt Calibration Switches ...............................................................3-4
Simultaneous Sample and Hold ........................................................3-4

Configurable Settings in MAX ......................................................................................3-4

NI-DAQmx......................................................................................................3-5

Creating a Strain Global Channel or Task ........................................3-6
Creating a Custom Voltage with 

Excitation Global Channel or Task ................................................3-7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды