manualshive.com logo in svg

NI PXI-4220, Руководство пользователя

Поделиться
Скачать
NI PXI-4220 Скачать руководство пользователя страница 86

Chapter 5

Developing Your Application

NI PXI-4220 User Manual

5-16

ni.com

•

PXI-4220 Supported Properties

 in the LabVIEW 

VI, Function, & 

How-To Help

.

•

Application Note 025: 

Field Wiring and Noise Considerations for 

Analog Signals

 available at 

ni.com

. Go to 

ni.com/info

 and enter 

the info code 

rdfwn3

.

Calibrating the NI PXI-4220

There are two types of calibration used to improve the accuracy of the 
NI PXI-4220. Device calibration ensures the accuracy of the NI PXI-4220. 
System calibration removes the offset and gain errors, two sources of 
potential measurement errors.

Calibrating the NI PXI-4220

The NI PXI-4220 is shipped with a calibration certificate and is calibrated 
at the factory to the specifications described in Appendix A, 

Specifications

. 

Calibration constants are stored on the NI PXI-4220.

Internal Calibration Procedure

The NI PXI-4220 incorporates internal calibration paths that allow routing 
channel inputs to ground or to an onboard high-precision reference voltage. 
NI driver software disconnects the channel inputs from the front signal 
connector and reconnects the inputs to ground or to an onboard reference 
when performing an internal two-point calibration. The driver software 
determines the correct adjustment factors for offset and gain error and 
stores them as calibration constants. The driver software automatically uses 
these adjustment factors to correctly scale each measurement. You need not 
change any input connections for an internal calibration.

To obtain the highest level of accuracy, you should periodically perform an 
internal calibration. You can self-calibrate the NI PXI-4220 within MAX.

To perform a self-calibration, complete the following steps:

1.

Double-click the 

Measurement & Automation Explorer

 icon on the 

desktop.

2.

Display the list of devices and interfaces by clicking the 

+

 next to the 

Devices and Interfaces

 icon.

3.

Display the list of NI-DAQmx devices by clicking the 

+

 next to 

NI-DAQmx Devices

 icon.

4.

Right-click the NI PXI-4220 and select 

Self-Calibrate

.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PXI-4220






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды