© 2020 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
169
PLUMBING
Switching On The Appliance
1. Open the access door.
2. To switch on the appliance, switch the POWER switch
to one of the two “ON” positions.
•
Both ON positions on the POWER switch have the
same function. Choose your preferred position.
•
When the green power ON LED 1 is lit, the
appliance is switched on.
•
If the red error code LED 2 is lit / flashes, there is a
fault or warning.
With the rotary switch you can
choose between the following
operating modes:
Operating Modes (Control
Panel)
•
The appliance is now ready for using the control
panel inside your vehicle.
Symbol /
Operating
Mode
Description
ECO
The appliance is now running in energy-saving mode.
•
Water temperature at the outlet is approximately 120 °F (49 °C).
•
Prevention of freezing by using propane gas. The temperature
in the appliance is automatically kept above 41 °F (5 °C).
•
During operation, the yellow status LED 3 is lit.
COMFORT
The appliance is now running in a mode that provides rapid availability
of hot water.
•
Water temperature at the outlet is approximately 120 °F (49 °C).
•
Stand-by heat. The temperature in the appliance is
automatically kept above 102 °F (39 °C).
•
During operation, the yellow status LED 3 is lit.
OFF
Stand-by. The appliance is not running in any operating mode.
•
The yellow status LED 3 is o
ff
. To switch o
ff
the POWER and gas
supply, refer to “Switching OFF the appliance”.
ANTIFREEZE
Prevention of freezing using 12 VDC electricity:
•
Operating mode with installed electric antifreeze kit (available
as an accessory) and appliance switched on. The temperature
in the appliance is automatically kept above 41 °F (5 °C).
•
During operation, the yellow status LED 3 is lit.
CLEAN
Decalcification. Only AquaGo Comfort / AquaGo Comfort plus. See
“Decalcification”.
•
For safety reasons, after 30 seconds the decalcification
process cannot be stopped until the system has been
rinsed in accordance with the instructions. See “Interrupting
decalcification”.
A control panel to select the
operating mode.
AQUAGO COMFORT / AQUAGO
COMFORT PLUS
AQUAGO COMFORT / AQUAGO
COMFORT PLUS
Risk of damage in frost conditions. In frost conditions,
ambient temperatures below 39 °F (4 °C), there is a
risk that water in pipes, faucets and appliances could
freeze. This can cause considerable damage. If the
appliance is not to be used in frost conditions, you
must winterize the appliance. Winter operation will
not protect the RV’s entire water system. Water lines,
faucets, water tanks and the external water valves
and the vehicle must be heated separately. The RV
must be designed for winter use/freezing conditions.
The water pipes in the RV must be ice-free to operate
the AquaGo Comfort / AquaGo Comfort plus in
winter. Otherwise, there is no water flow and the
appliance does not start.
NOTICE
!
DESCRIPTION OF THE YELLOW
STATUS LED 3
ONLY AQUAGO COMFORT / AQUAGO
COMFORT PLUS
Switching Off The Appliance
1. AquaGo Comfort / AquaGo Comfort Plus
•
Set the control panel to “O
ff
”.
2. Open the access door.
3. Switch o
ff
the appliance at the POWER switch.
•
The green Power-ON LED 1 extinguishes.
4. Close the access door.
5. If the appliance is not needed, turn o
ff
the gas supply
to the appliance.
•
If you intend to put the RV into storage or turn o
ff
the appliance during freezing temperatures.
(Ambient temperatures below 39 °F (4 °C))
Operation In Frost Conditions
When the vehicle is standing, to -4 °F (-20 °C):
•
The appliance has a built-in thermostat that will start
the burner and the circulation pump whenever the
temperature in the appliance falls below 41 °F (+5 °C).
The burner will automatically shut o
ff
when it senses a
temperature above 111 °F (44 °C).
Signal
Meaning
LED 3 is lit
Appliance is switched ON
LED 3 is o
ff
Appliance is switched OFF.
Every 7 s, LED 3 is interrupted
for 1 s
The appliance must be decalcified
LED 3 flashes slowly 1 s on, 1 s o
ff
Decalcification mode has been activated
LED 3 flashes quickly
Before you use the water system you must
rinse it.
LED 3 flashes 2 x briefly after a
break.
There is a fault in the appliance. The exact
fault diagnosis must be determined via error
LED 2. Risk of freezing if the temperature in
the appliance is below 37.4 °F (3 °C).
Содержание Canyon Star 2021
Страница 1: ...2021 sm ...