Ness SmartLiving 10100 Скачать руководство пользователя страница 95

Страница: 95 / 112

Installation and programming manual

Errors and faults

Chapter 8

ERRORS AND FAULTS

8-1

Faults detected by the

control panel

The following table shows the system faults which are signaled on the yellow LED on the

keypad

FAULT

Message on the User menu,

“View/Faults”

Probable cause

Note

Zone fuse blown

Zone fuse fault

Excessive current draw on the “+AUX” terminals

of the control panel

BUS fuse blown

IBUS fuse fault

Excessive current draw on the “+” terminal of

the control panel

Backup battery ineffi-

cient or not connected

Low battery

The backup battery of the control panel is

almost empty or disconnected.

Primary power-source

loss

Mains failure

The primary power source voltage (230 Vac) has

failed or has been disconnected

The PSTN landline is

unavailable

Tel. line down

Trouble on the PSTN landline

Interference

Jamming

Wireless transmission is poor

Wireless detector bat-

tery low

Low battery WLS

The battery of at least one wireless detector is

running out

To view “LowBatt. battery WLS”

and “WLS zone loss” signaling,

access the user menu, go to

“View/Faults”, press

to view

the list of devices involved.

Wireless detector not

operative

WLS zone loss

At least one wireless detector is not operating

Nexus GSM dialer

faults

Nexus fault / Low signal

The GSM network signal is insufficient

Press

on “Nexus fault” to

access the list of current faults.

Nexus fault / GSM module

fault

The GSM module of the Nexus dialer is not oper-

ating properly. Call your Installer company

Nexus fault / SIM com-

mun.fault

The SIM card does not respond or is not present.

The SIM card PIN is not disabled.

Nexus fault / Low Credit

The credit left on the SIM card is below the

minimum credit threshold.

Nexus fault / ProviderUnavail-

able

The GSM network provider of the SIM in use is

unavailable.

Nexus fault /GPRS conn. lost

NEXUS/G detects problems on GPRS network

communications

IP connection loss

IP conn. lost

The verification of the IP connection fails.

Device loss or tamper

in progress

LossTamp.ongoing

One of the following events has occurred:

•

Control panel open

•

Dislodged panel

•

Expansion tamper

•

Keypad tamper

•

Reader tamper

•

Sound.flash.Tamp

•

Expansion loss

•

Keypad loss

•

Reader loss

•

Sound.flash.Loss

Содержание SmartLiving 10100

















































































































Результаты поиска

Содержание SmartLiving 10100

Отзывы:

Похожие инструкции для SmartLiving 10100

Бренды по названию

Популярные бренды

Ness SmartLiving 10100, Инструкция по установке и программированию

Результаты поиска

Содержание SmartLiving 10100

Отзывы:

Похожие инструкции для SmartLiving 10100

Бренды по названию

Популярные бренды