manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 55

 

 

 

101-000                                                 -55-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

☞ 

Can I set the controller to operate in RF only mode for one card and in RF+P/W mode for another?

Cause 

N/A 

Solution 

1. Do not mix the working mode for one Reader.   
2. But you can set one reader to operate in RF only mode and another one in RF+P/W mode.   

 

☞ 

The Setup mode suddenly goes back to the Normal-operating mode.

 

Cause 

Time out error 

Solution 

1. In the Setup mode, it is programmed to do so when there is no key-in or reading card within 

60 seconds. 

   

 

☞

 Keep making buzzer sound: “beep~ beep ~ beep” or “beep~~~~”. 

Cause

 

Error in installation, door status or internal circuits. 

Solution

 

1. Check the door status. It occurs in case that the door is opened over 20 sec after the proper 

door open time.   

2. Check the door contact sensor type: it should be NO type. 
3. Check in [IN/OUT DEFINE] of F2, the fifth Time schedule code (01~10) value of 15 output 

T/S. If the time schedule code is set between 01-10 and if the present time is included in the 
schedule.  

If it is set to unintended value, change it to “00” (Programmable via PC software) 

4. If the trouble remains after checking the above, contact a designated service center. 

☞ 

The reader seems to read cards, but the controller does not respond or does not respond properly, 

such as displaying wrong card numbers in the reader test mode.

 

Cause 

Reader defect, wiring error between the reader and the controller, or the electric noises around. 

Solution 

1. Be sure that the reader reads the card ID when you present a card. 
2. Be sure that the reader format is correct. 26bit Wiegand. 
3. Check the wiring between the reader and NESS - iCON100. 

-

 

Check the wires of Wiegand data lines D0 and D1 that is connected correctly. 

-

 

Connect the controller ground to the ground wire of the reader and it is recommended to 
connect them to an earth ground. 

4. Using oscilloscope, check the shape of signals from the reader at the controller’s side. 

When noises are shown on the signals, it is recommended to use shielded wires and the 
unused wires to the common ground. You can use repeaters, also. 

5. Check the maximum cable length, which may be indicated on the reader manual. 
6. If the trouble remains after the procedure above, contact a designated service center. 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды