Ness IDTECK iCON100 Скачать руководство пользователя страница 25

Страница: 25 / 60

101-000 -25- Users Manual

IDTeck – iCON 1 DOOR ACCESS CONTROLLER

6.3 DIAL UP MODEM

Please, see the software manual.

6.4 TCP/IP CONVERTER (EXTERNAL VERSION)

Please, see the software manual.

7. BASIC SETTINGS

Note !!!

You have to connect an LCD display and keypad to the iCON100 for the following manual

settings.

7.1 INITIALIZATION OF NESS - iCON100

After the all installation and connections are completed, put the power (+12V DC) to the NESS -
iCON100 then toggle the switch 8 to 'off' and toggle it back to 'on'. The LCD will first display
“

System

Initializing…

” After the all Initialization process is completed then the LCD will display

“

Initialize END Turn OFF Power.

” Turn the power off then turn it on again for the NESS -

iCON100 to start

7.2 HOW TO ENTER THE SETUP MENU

To setup or to change the NESS - iCON100 settings, you have to enter the

SETUP MENU

first. To do

so, press the

<0>

key eight times for the

Master ID

(

Default setting “00000000”

) followed by the

<ENT>

key. There are four main

SETUP MENUs.

You can move through the

SETUP MENUs

pressing the

<F1>,

<F2>

<F3>

<F4>

keys. There are several

SUB MENUs

in the main

SETUP

MENU.

You can scroll through the

SUB MENUs

by pressing the

<4>

and

<6>

keys. If you don’t

press any key for 60 seconds or if you press the

<ESC>

key then the NESS - iCON100 will exit the

SETUP MENU

and return to normal operation.

Initialize END
Turn OFF Power..

System
Initializing...

Содержание IDTECK iCON100





























































Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды

Ness IDTECK iCON100, Руководство пользователя

Результаты поиска

Содержание IDTECK iCON100

Отзывы:

Бренды по названию

Популярные бренды