manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 24

 

 

 

101-000                                                 -24-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

6.2.2 RS-422 CONNECTION (MULTIPLE iCON100 CONNECTIONS) 

An RS422/RS232 converter is required to use RS422 communication between multiple 
NESS -iCON100s and a host computer. Please follow the following instructions. 

 

First, you have to connect all RS422 port of all NESS - iCON100s in parallel. 
- Connect RS422-TX (+) of one iCON100 to RS422-TX (+) of another iCON100. 
- Connect RS422-TX (-) of one iCON100 to RS422-TX (-) of another iCON100. 
- Connect RS422-RX (+) of one iCON100 to RS422-RX (+) of another iCON100. 
- Connect RS422-RX (-) of one iCON100 to RS422-RX (-) of another iCON100. 

 

Then connect the RS422 port of the NESS - iCON100 to the RS422/RS232 converter.   
- Connect RS422-TX (+) of the one iCON100 to RX (+) port of the converter. 
- Connect RS422-TX (-) of the one iCON100 to RX (-) port of the converter. 
- Connect RS422-RX (+) of the one iCON100 to TX (+) port of the converter. 
- Connect RS422-RX (-) of the one iCON100 to TX (-) port of the converter.   
- Plug in the RS232 9-pin connector of the converter to the COM1 or COM2 Port of the PC. 
- Install and run NESS iCON100 Application Software. 

 

 

 

    Figure: RS-422 Communication between NESS iCON100s and Host Computer 

 
 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды