manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 35

 

 

 

101-000                                                 -35-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

9.1.7 EVENT CLEAR

 

 
 
 
 
 
 
 
 
 
 
 
 
 

9.1.8 MASTER ID CHANGE

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

BAUD RATE 

->9600 

BAUD RATE 

->19200 

Master  Card 

  Registered 

MASTER ID CHANGE 

[________] 

☞

. Press the <ENT> key to change the current Master ID 

(“00000000”). You should use the new Master ID to access the 
SETUP MENU after you have changed the Master ID. 

☞

. The Master ID is now changed and stored in the memory. The 

LCD shows new Master ID is registered successfully.

 

MASTER ID CHANGE 

☞

. 

You should use an 8 digit number for the Master ID. Press the <ENT> 

key, then enter the new 8 digit Master ID and the <ENT> key.

 

EVENT  CLEAR 

 1 - Yes,  0 - No 

EVENT  CLEAR 

☞

. When the event memory is full or when you want to change the 

ID COUNT, you can clear the event memory in this menu. Press 
the <ENT> key then press the <1> key to clear event memory or 
<0> key to cancel the operation. 

CAUTION: Before you clear the events, make sure that your 

stored events are uploaded to the host PC otherwise 
you may lose important data. 

 

☞

. If you have a communication problem, please check the following; 

- COMM ID of NESS - iCON100 and host PC 
- BAUD RATE of NESS - iCON100 and host PC 
- Communication port and cable 
- COM port setup of host PC default setting is; 

Parity: None, Data Bit: 8 bit, Stop Bit: 1 bit 

To change the baud rate, press the <ENT> key and select desired baud 
rate by pressing the <4> or <6> keys then press the <ENT> key.

 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды