manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 34

 

 

 

101-000                                                 -34-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 

9.1.3 TIME SETTING

 

 
 
 
 
 
 

 
 
 
 
 
 
 

9.1.4 ANTI-PASS-BACK MODE SETTING

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

9.1.5 COMMUNICATION ID (ADDRESS) DISPLAY

 

 
 
 
 
 
 
 

   

 

9.1.6 BAUD RATE SETTING 

 
 
 
   
 
 
 
 

APB SETUP

  

NOT USE 

APB SETUP

 

->USE 

☞

. It shows the anti-pass-back operation is not used. Press the <ENT> key. 

(

It only applies when the Door has an Exit Reader

) 

 

You must have Reader #1 for entry and Reader #3 for exit. 

☞

.   Press the <4> or <6> key for searching the APB mode. 

Press the <ENT> key to select the mode. 
NOT USE: Anti-pass-back mode is not applied. 
USE: Anti-pass-back mode is separately applied. 

APB SETUP

 

->All Clear 

☞

. If you select All Clear then the NESS - iCON100 will clear all 

APB flags.

TIME SETTING 

YYYYMMDDhhm

mssW 

☞. 

Press the <ENT> key and enter the 15 digit Date/Time codes 

then the <ENT> key to finish the setting. 
YYYY: Year, MM: Month, DD: Date hh: Hours (24 hours 
system), mm: Minutes, ss: Seconds 
W: Sun=1, Mon=2, Tue=3, Wed=4, Thu=5, Fri=6, Sat=7 

Example: 200302101330152 => Feb.10,2003 13:30:15 Mon 

COMM ID 

00 

BAUD RATE 

9600 

☞

. This menu shows the current communication ID of the NESS 

iCON100. If multiple iCON100 units are connected to one host 
PC, each unit must be configured to different communication ID. 

Note: 

You can change the COMM ID by DIP switch setting of the 
NESS - iCON100. 

☞

. The NESS - iCON100 supports 4800, 9600, 19200 and 38400bps 

of baud rate and the default setting is 9600bps. Wrong baud rate 
settings will cause communication errors. You have to set the 
same baud rate in the NESS - iCON100 and the host PC. 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды