manualshive.com logo in svg

Ness IDTECK iCON100, Руководство пользователя

Поделиться
Скачать
Ness IDTECK iCON100 Скачать руководство пользователя страница 10

 

 

 

101-000                                                 -10-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

RS-232 Serial Communication Port 

This is an RS232 communication port for connecting this board directly to a PC.   

 

RS-422 Serial Communication Port 

This is an RS422 communication port for connecting up to 256 units to a PC.   
You need an RS422/RS232 converter for connecting the RS422 port to a PC. 

Keypad 

This is an optional keypad port and it can be used with an optional LCD display module for manual 
setup. 

LCD Display 

This is an optional LCD Display port and it can be used with an optional keypad for manual setup. 

Jumper 

This is a Battery Connection Jumper. You have to short circuit this jumper before you use the NESS - 
iCON100 control board, as this jumper is for the connection of a backup battery to the internal 
memory devices. 

Reader #1 ~ Reader #2 

These are two proximity reader ports. Each reader port supplies DC12V to the proximity reader and 
receives 26bit wiegand output from the reader. If you connect a PINPAD Reader then you have to 
make sure that the PINPAD Reader has 8bit burst wiegand output. 

Input #1 ~ Input #5 

These are five Input Ports. 

RL #1 ~ #2: 

These ports are to be connected to the control signal line of a buzzer or an LED of a reader, to show 
the operation status of relay #1 or relay #2. 

Buzzer 

This is an internal buzzer, which sounds when you press the keys on a keypad to allow for easy 
confirmation of the keys being pressed. 

Reader 1 Jumper (Reader #2 Jumper): 

 

This is not for user or installer operation

.

 

 

LED #1 ~ LED #2 

These two LEDs indicate communication status. LED #1 is RX status and it blinks when the data is 
being received from the PC. LED #2 is TX status and it blinks when the data is transmitting to the PC 

LED #3 

This red coloured LED is a power indicator, which is always on when the control board is powered up.

 

LED #4 ~ LED #5 

These two LEDs indicate the relay output status. Each LED is on when the corresponding output is 
activated. LED #4 is for Relay #1; LED #5 is for Relay #2. 

 

Содержание IDTECK iCON100





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды